A320 FMGS B48

[startrail]

I can't recommend any it's dependent on your hardware. There is some info in the documentation.

Thank you for your assistance. Calibration was the problem. I had to do it many times and finally it worked. Once again thank for your kind attention.RegardsMike

[romeow]

AP1+2: the normal AP take over buttons should do that just fine?

Thank you for this hint, jeehell!

Now everything works fine! But the main "problem" was an additional configuration within FSUIPC for the sidestick push button (which had nothing to do with AP)! I don't know why and when I assigned a "keysend" to this push button. But whyever it was my stupidity.
Regards
René

[startrail]

Hi Folks ..!

Released new version for Jeehell Fmgs sounds.
Version V4:
New engine sounds and environment.
Double version CFM, AIE-V2500
Boosted bass boost and equalization gain.
New PTU sound.
Installation:
Copy the files to the folders corresponding to CFM and AIE.
The PTU sound in the "sound" folder in the fmgs server.
Download

Link temporary off line


Best

Daniele

Hi Daniele,

how can I download the new sound set.


Thanks

Mike

[Migelito]

Hyi Jeehell, hyi all!

Please does anyone know, is B48.2.2 working with P3D v4.1?
And to click P3D 4.0 during setup (because of missing 4.1 possibility)?
Sorry if I missed something

Thanks for help
Michael

[startrail]

Hyi Jeehell, hyi all!

Please does anyone know, is B48.2.2 working with P3D v4.1?
And to click P3D 4.0 during setup (because of missing 4.1 possibility)?
Sorry if I missed something

Thanks for help
Michael

Yes it does.


Mike

[Migelito]

Thanks for quick answer, very kind.

Michael

[Fritz]

Hi to all,

when I touch the ground I switch to reverse thrust but the autothrust gives full thrust as for a go-around. Even if I set to idle, he gives full thrust. The throttle (Skalarki TQ) is connected on a client where FMGS server is installed. Prepare 3D v4.1 runs on a visual PC. Wide FS is installed and connected. Skalarki Profiler also runs on the client.
Everything works well but when landing, he always gives full thrust.

Have already tried a lot to solve the problem but now I have no idea why that could be.
I had the problem once and then it was gone. Whether it has something to do with the update of Prepare 3D to 4.1?

[Migelito]

Hyi JL!

Trying to place FMGS Server on a PC not running P3D.
Funnywise I can´t get connection to a ND running on this same PC which runs FMGS Server.
On the client PC (No P3D/No FMGS Server) I do get some connections (MCDUs), some don´t work (PFDs, NDs).

Of course network and A320FMGS setup correctly, always worked in 2PC Configuration.
I´m thankful for any idea or advice

Thanks and kind regards
Michael


@Fritz: Leider Fritz habe ich keine Antwort für dein Problem. Du bist der Einzige den ich kenne, der selbiges Setup
mit v4.1 und ausgelagertem Server zum Laufen gebracht hat. Dürfte ich dich außerhalb des Forums kontaktieren?
Das wäre eine riesen Hilfe für mich. Falls ja, bitte schreibe zurück unter michael.neswadba@gmail.com, somit brauchst du keine pers. Daten im Forum preisgeben. Ich danke dir im Voraus, liebe Grüße Michael

[Fritz]

Hi Miachael,

Check the following:
IP addresses set correctly for P3D Visual PC and Server PC?
ND.exe runs with adminsitrator rights?
Do you possibly use Norten? Then exclude ND.exe from the scan and firewall.
Have you configured a DU dimmer for the ND? Maybe the display is dimmed.

You can also write a PM.

[jeehell]

Hi to all,

when I touch the ground I switch to reverse thrust but the autothrust gives full thrust as for a go-around. Even if I set to idle, he gives full thrust. The throttle (Skalarki TQ) is connected on a client where FMGS server is installed. Prepare 3D v4.1 runs on a visual PC. Wide FS is installed and connected. Skalarki Profiler also runs on the client.
Everything works well but when landing, he always gives full thrust.

Have already tried a lot to solve the problem but now I have no idea why that could be.
I had the problem once and then it was gone. Whether it has something to do with the update of Prepare 3D to 4.1?

Check again your calibration and detents