Results 1 to 5 of 5
  1. #1
    25+ Posting Member
    Join Date
    Jul 2015
    Location
    Germany/Saxony/EDCJ
    Posts
    71
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Jeehell and IvAp (IVAO)

    Hello,
    is anybody using Jeehell in connection with IvAp (IVAO Network)?
    My questions are about:
    - Install IvAp on dedicated PC? How connect to FMGS Server / P3D ?
    - PTT button on Sidestick, connect to FMGS or Teamspeak?
    - Teamspeak on which PC, interaction with Skalarki P&P Panels on RMP Modul possible?
    - TCAS from IvAp ineracting with ND display?

    Thanks for sharing your experience with this setup.

    best regards,
    Frank
    Prepar3D v5, Jeehell Ware latest Beta, all Skalarki P&P Panels, Active Sky, ASCA

  2. #2
    300+ Forum Addict asessa's Avatar
    Join Date
    Oct 2012
    Location
    Salerno , Italy
    Posts
    474
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Re: Jeehell and IvAp (IVAO)

    Hi , i always use JL and Ivap..

    1. What do you mean? Ivap and JL don't comunicate
    2. You have to set by fsuipc a key (not used by sim or other) to a joy button. Then set in TS that key as PTT.
    3. I have RMP by CockpitSonic and when i switch frequencies i have same switch in ivap and sim without any problems.
    4. Yes it does

    Hope this help
    P3D V5 HF1 - PC spec: Intel i5-6600K, 16 GB DDR4 2400, GPU Nvidia GTX1070ti, M2 SSD NVme, JH FMGS, GSX, ASP3D+ASCA+ENVSHADE

  3. #3
    2000+ Poster - Never Leaves the Sim


    OmniAtlas's Avatar
    Join Date
    Jun 2012
    Location
    Sydney, Australia
    Posts
    2,107
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Re: Jeehell and IvAp (IVAO)

    There should be an opportunity to interface IVaP or a Vatsim client with the FMGS software audio control panel. There was a bug fix JL mentioned was corrected and will be implemented in the next release.
    Soarbywire - Airbus Flight Simulation and Engineering | Jeehell FMGS - Free professional A320 avionics software for the cockpit enthusiast.


  4. #4
    25+ Posting Member
    Join Date
    Jul 2015
    Location
    Germany/Saxony/EDCJ
    Posts
    71
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Re: Jeehell and IvAp (IVAO)

    Thanks for the answers.
    So a detailed question:

    To 1.:
    I have 4 PC's:
    1) P3D with Jeehell, AS16, ASCA, Skalarki I/O Profiler
    2) PC for CPT's PFD/ND and MCDU
    3) PC for FO's PFD/ND and MCDU
    4) PC for ECAM ...

    So I would set up PC 5 with OIS, EFB, Charts and also IvAp and Teamspeak.
    Then I can interact and set . commands in IvAp oder should I install Teamspeak on PC 1?
    Can IvAp act as Server / Client, that means running on PC 1 in background and the IvAp Panel on PC 5?

    thanks for any hints,
    Frank
    Prepar3D v5, Jeehell Ware latest Beta, all Skalarki P&P Panels, Active Sky, ASCA

  5. #5
    25+ Posting Member
    Join Date
    Jul 2015
    Location
    Germany/Saxony/EDCJ
    Posts
    71
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Re: Jeehell and IvAp (IVAO)

    Solution found,
    There is needed the registrated version of FSUIPC and WideFS.
    With FSUIPC connect an unused short cut (for me F12 key) with the PTT switch of the sidestick.
    Make this event available on WideFS server. With the WideFS client, connect the event to the TeamSpeak Program.

    For the Traffic on ND I have no solution but:
    With default AI Traffic of P3D, the ND shows the Traffic what I can see also on the visual.
    With the MTL Traffic of IVAO I can see it also on my visual output, but not on ND. For this I have to open the TCAS window of IvAp additionally. Why can Jeehell not display it on ND?

    best regards Frank
    Prepar3D v5, Jeehell Ware latest Beta, all Skalarki P&P Panels, Active Sky, ASCA