Results 31 to 40 of 41
Thread: Overhead with InterFaceIt
-
12-06-2016, 05:22 PM #31
- Join Date
- Mar 2008
- Location
- France,Nice
- Posts
- 2,652
Re: Overhead with InterFaceIt
The same assumption is used. For the middle position, use the same action but with sw up event.
-
12-06-2016, 05:50 PM #32
- Join Date
- Jan 2007
- Location
- Italy
- Posts
- 204
-
12-06-2016, 05:55 PM #33
- Join Date
- Jan 2007
- Location
- Italy
- Posts
- 204
Re: Overhead with InterFaceIt
Further testing...when i start the software the position of other switches are recognised fine but the EMER EXT LT not...
-
12-10-2016, 02:26 PM #34
- Join Date
- Jan 2007
- Location
- Italy
- Posts
- 204
Re: Overhead with InterFaceIt
Hi, found something... i want a switch to work in reverse order specifically the Overhead Beacon, i want to assign 1st action on SWdown Beacon OFF and in SWup Beacon On when i save it and reopen in ittcreator they are both OFF tried many times but not work...
2) sometimes after a little the led assignment action list become all white and can't select nothing minor issue...you have to restart creator to populate again.
Update 1: also RWY turnoff don't work well
-
12-12-2016, 11:58 AM #35
- Join Date
- Jan 2007
- Location
- Italy
- Posts
- 204
-
12-12-2016, 05:57 PM #36
- Join Date
- Mar 2008
- Location
- France,Nice
- Posts
- 2,652
Re: Overhead with InterFaceIt
here seems the good place...
I do not see what are your problems? What was possible in previous IIT version is still possible?
-
12-12-2016, 06:58 PM #37
- Join Date
- Jan 2007
- Location
- Italy
- Posts
- 204
Re: Overhead with InterFaceIt
Ok, i try to explain here but it will be better to have a chat anyway, let's start with the 3 position switches problem (we just try with no smoking OFF-AUTO-ON) here is an example that you can verify first the configuration on ITT:
Switch n.1:
On switch down: OVHD NOSMOKING OFF - assigned action switch down
On switch Up: OVHD NOSMOKING OFF - assigned action switch up
Switch n.2:
On switch down: OVHD NOSMOKING ON - assigned action switch down
On switch Up: OVHD NOSMOKING ON - assigned action switch up
Now my hardware switch is set to OFF if we start the FMGS it perform the first scan of switches and because the last switch with the same function in this case number 2, it put the overhead software switch to AUTO (different than my hardware position) this is why:
IT think scan switch 1 is it down? yes so put it to OFF
then scan switch n.2 is it down? no is up so put to AUTO
here is the bug, after the initial scan you have to make a subroutine for those type of switches where the last assumption is based on a different logic here is an example:
Scan performed so now we need a subroutine to check:
if
switch1 down and switch2 up put it to OFF
or
switch2 down and switch1 up put it to ON
Else
put it to AUTO
So it will get in sync with the first startup either i have to cycle all the switches to sync them correctly.
Hope i was clear any thoughts?
-
12-13-2016, 12:18 PM #38
- Join Date
- Mar 2008
- Location
- France,Nice
- Posts
- 2,652
Re: Overhead with InterFaceIt
I see your problem. I will try to add some more logic later on, not much time to work on FDS interface...
JL
-
08-01-2017, 11:21 AM #39
- Join Date
- Jan 2007
- Location
- Italy
- Posts
- 204
Re: Overhead with InterFaceIt
Hi, have you corrected this?
-
08-01-2017, 11:29 AM #40
- Join Date
- Mar 2008
- Location
- France,Nice
- Posts
- 2,652
Re: Overhead with InterFaceIt
not yet..
JL
Looking for fun companions for travels and adventures? Authentic Ladies Premier Сasual Dating
Top-notch Сasual Dating -...