Page 32 of 32 FirstFirst ... 222829303132
Results 311 to 319 of 319

Thread: A320 FMGS B46

  1. #311
    25+ Posting Member
    Join Date
    Dec 2004
    Posts
    71
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Re: A320 FMGS B46

    If you are using FDS boards, have you used IITcreator for the switch and led assignments?

    I have very recently moved from a well known A320 software suite to Jeehell which required a complete reassignment exercise including using IITcreator.
    Initially I had a problem as Gen1 and Gen2 would not come on line although all the start-up procedure was correct.

    To cut a long story short, I found that the problem was my IDG switches and how they were assigned (up/down/toggle) in IITcreator. The physical attributes of the switches were different to all my other switches. What was happening, because of the way the switch was configured, the IDGs must have been disconnecting straight after powering up the aircraft.

    Initially I thought it was a software problem but dismissed that as the start sequence was fine if I used the graphical software without starting my hardware boards.

    I'm finding that any errors in your hardware setup will cause problems since the software's logic is excellent!

    The IITcreator has a couple of bugs in it e.g. the IDS 2 and 3 Allign leds are the wrong way round...

    Regards,
    Darren Sugden

  2. #312
    75+ Posting Member anzabon's Avatar
    Join Date
    Apr 2014
    Location
    Moon Base
    Posts
    78
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Re: A320 FMGS B46

    Hello Jean-Luc,

    thank you for your recommendation to check the fire handles... since the APU fire handle assignment is inverted here and one of the wire had lost contact to the micro switch the system thought APU fire handle was active. So that has been the reason for the failures.
    Thank you very much for your help!

    Only the APU still doesn't run down after switching off on the OVHD. It simply continues running...

    Kind regards,
    Bon

  3. #313
    New Member
    Join Date
    Dec 2016
    Location
    Madrid
    Posts
    3
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Re: A320 FMGS B46

    Quote Originally Posted by anzabon View Post
    Hello Jean-Luc,

    thank you for your recommendation to check the fire handles... since the APU fire handle assignment is inverted here and one of the wire had lost contact to the micro switch the system thought APU fire handle was active. So that has been the reason for the failures.
    Thank you very much for your help!

    Only the APU still doesn't run down after switching off on the OVHD. It simply continues running...

    Kind regards,
    Bon
    I have checked that, and the sames happens to me. Once I have APU running and engines started, when I try to stop the APU, it remains still with AVAIL on.

    I haven磘 investigated that yet, because I am just starting and performing some test.

  4. #314
    2000+ Poster - Never Leaves the Sim
    Join Date
    Mar 2008
    Location
    France,Nice
    Posts
    2,652
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Re: A320 FMGS B46

    The APU runs for about 2 minutes after APU bleed has been used (even for a fraction of seconds) as a cooldown period. It will stop automatically when this cooldwon phase is over (and master SW was initially pushed of course).

  5. Dislikes Paktom disliked this post
  6. #315
    300+ Forum Addict
    Join Date
    Sep 2010
    Location
    LGTS
    Posts
    424
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Re: A320 FMGS B46

    Hi
    Anyone using ATC-PRO/X? I can't get Clearance at the beginning, even though I tune proper freq. All others freq. operate properly (ATIS, Depart etc).
    This is not off topic cos I've read in a ATC-PRO/X forum discussion that this Clearance doesn't work for some addons and I hope JeeHell is not one of them.
    Thank you

  7. #316
    300+ Forum Addict
    Join Date
    Sep 2010
    Location
    LGTS
    Posts
    424
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Re: A320 FMGS B46

    Hi
    The volume of JeeHell Sound application drops to 5-10% in Windows Sound Mixer. This happens 2-3 times every flight time. Anyone with same issue?

  8. #317
    25+ Posting Member



    Join Date
    Feb 2015
    Location
    Austria
    Posts
    49
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Re: A320 FMGS B46

    Quote Originally Posted by Leonidas View Post
    Hi
    The volume of JeeHell Sound application drops to 5-10% in Windows Sound Mixer. This happens 2-3 times every flight time. Anyone with same issue?
    Hello,

    I have a similar sound problem. The volume drops after position changes in p3d or pause activation.reseting the flight in p3d will set the default volume....


    Robert

  9. #318
    25+ Posting Member
    Join Date
    Jul 2013
    Location
    Switzerland
    Posts
    31
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Re: A320 FMGS B46

    Hey Guys

    Have you tried switching the position in "sound" settings "communications" tab to "do nothing"?

    https://superuser.com/questions/4500...ndows-7-64-bit

    Best regards

    Daniel


    Quote Originally Posted by fisfro View Post
    Hello,

    I have a similar sound problem. The volume drops after position changes in p3d or pause activation.reseting the flight in p3d will set the default volume....


    Robert

  10. Thanks Leonidas thanked for this post
    Likes Leonidas liked this post
  11. #319
    2000+ Poster - Never Leaves the Sim
    Join Date
    Mar 2008
    Location
    France,Nice
    Posts
    2,652
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Re: A320 FMGS B46


  12. Likes asessa liked this post
Page 32 of 32 FirstFirst ... 222829303132