Page 2 of 2 FirstFirst 12
Results 11 to 15 of 15
  1. 03-18-2016, 10:21 AM #11
    Hypnorm
    Hypnorm is offline
    25+ Posting Member
    Join Date
    Feb 2008
    Location
    Perth, Australia
    Posts
    39
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Re: A320 Overhead panels

    Hi again Les,

    I have uploaded the files for constructing the MIP carcass. Again, it is sketchup files, (easily exported to DXF) and designed for 9mm MDF.

    Note that is for a one man cockpit (captain side and ECAM) although it could be easily adapted for a 2 man cockpit by adding another centre and floor and extending the back and top.

    Hope it's useful.

    Happy building,

    Jim
    Reply With Quote Reply With Quote
  2. 03-18-2016, 12:47 PM #12
    iwik
    iwik is offline
    500+ This must be a daytime job


    Join Date
    Jan 2007
    Location
    NEW ZEALAND
    Posts
    908
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Re: A320 Overhead panels

    Thanks Jim,
    That's Perfect as i can only accommodate a single man cockpit. Thought i was going to have to modify it.
    Regards
    Les
    Reply With Quote Reply With Quote
  3. 03-21-2016, 12:13 AM #13
    Buddym
    Buddym is offline
    300+ Forum Addict
    Tutorial Contributor / Point Value: 10
    Total Awards: 1
    Total Points: 10



    Join Date
    Jan 2009
    Location
    Tampa
    Posts
    487
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Re: A320 Overhead panels

    great looking panels! what are you going to do for a throttle? If you have access to a 3d printer, I have throttle handle files....

    Reply With Quote Reply With Quote
  4. 03-21-2016, 12:34 AM #14
    Hypnorm
    Hypnorm is offline
    25+ Posting Member
    Join Date
    Feb 2008
    Location
    Perth, Australia
    Posts
    39
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Re: A320 Overhead panels

    Thanks Buddy ..... I may take you up on that

    For the moment, I'm working on layered throttle levers that look like this


    The prototype is in 6mm MDF but I will go to 6mm acrylic for the final. I haven't figured out the handle yet.

    I am lucky in that I live a 10 minute drive from Westozy - the throttle king!!! I will be going over to see him soon and pick his brains

    Cheers,

    Jim
    Attached Images Attached Images
    Reply With Quote Reply With Quote
  5. 03-21-2016, 02:45 AM #15
    Westozy
    Westozy is offline
    MyCockpit Support Staff
    Builder Of The Month / Point Value: 100
    Total Awards: 1
    Total Points: 100



    Westozy's Avatar
    Join Date
    Nov 2005
    Location
    Perth, Western Australia
    Posts
    1,415
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Re: A320 Overhead panels

    Hi Jim, I've PMd my phone number to you, catch up soon! Cheers Gwyn

    737NG using Prosim737, Immersive Calibration Pro, Aerosim Solutions motorized TQ & cockpit hardware, CP Flight MCP & FDS SYS1X, SYS2X & SYS4X, FDS PRO FMCs, AFDS units & Glarewings, Matrix Orbital ELEC display, Pokeys Landing & Cruise alt display, Buttkicker Gamers, 3 x BenqMW811ST projectors with a Matrox Th2Go
    http://www.aerosimsolutions.com.au
    Supporter of MyCockpit.org, please join me in donating!!!
    Reply With Quote Reply With Quote
Page 2 of 2 FirstFirst 12
« Previous Thread | Next Thread »