Results 1 to 5 of 5
  1. #1
    150+ Forum Groupie masterp's Avatar
    Join Date
    Jun 2015
    Location
    Ho Chi Minh City
    Posts
    190
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Rudder Trim Display - Offset

    Hi JL,

    I am planning to setup "7-segment displays" to display the rudder trim indicator of the bus. Example "L2.1" , "0.0" or "R1.3".
    Could you please let me know the offset value for those LEDs.

    my card is Arduino with mobiflight software, with below tutorial.
    http://www.mobiflight.com/en/tutoria...t-display.html

    Thanks

    P/S: I found this offset from FSUIPC documents, I may try and report later
    Offset Size Description
    2EC0 8 Rudder trim deflection, in radians, as a double (FLOAT64).

  2. #2
    2000+ Poster - Never Leaves the Sim
    Join Date
    Mar 2008
    Location
    France,Nice
    Posts
    2,426
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Re: Rudder Trim Display - Offset

    Hi,

    this offset will not work, currently no offsets will give this display state. I will try to add it in next release.

    JL

  3. #3
    150+ Forum Groupie masterp's Avatar
    Join Date
    Jun 2015
    Location
    Ho Chi Minh City
    Posts
    190
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Re: Rudder Trim Display - Offset

    Thanks JL.
    I will prepare all the LEDs first and wait for your offset code

  4. #4
    25+ Posting Member sstusek's Avatar
    Join Date
    Nov 2007
    Location
    Slovenia
    Posts
    45
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Re: Rudder Trim Display - Offset

    Hello JL

    While you are at it, could you please also check zeros displaying on rudder trim display. I have configured my rudder trim display in sioc-configurator and I get all three zeros on "00.0". I think there should only be two "0.0" and the third segment (DISP3) on when trim value exceeds "9.9" to "10.0" L or R.



    I added code in sioc to extinguish third segment 0 until value 1. It works fine but while trimming I get zero flickering on disp3 segment until trim value 10.

    Var 0005, name RUDTRIM_DISP3, Link IOCARD_DISPLAY, Device 3, Digit 73, Numbers 1
    {
    IF &RUDTRIM_DISP3 = 0
    {
    &RUDTRIM_DISP3 = -999999
    }
    }


    It is not that bad but if it can be sorted out it would be perfect , Thank you.
    Simon
    Attached Images Attached Images

  5. #5
    2000+ Poster - Never Leaves the Sim
    Join Date
    Mar 2008
    Location
    France,Nice
    Posts
    2,426
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Re: Rudder Trim Display - Offset

    Hi,

    FSUIPC offsets used will be $73B1 length 2 for the display, and $78ED values 77 to 80 for switch/selector.
    Not sure when the new version will come out yet, I hope in a few days.

    I corrected the SIOC issue at the same time.

    JL

  6. Thanks masterp, iwik thanked for this post
    Likes masterp liked this post