A320 FMGS B44

[asessa]

B44.2 all CockpitSonic devices are shutted down (FCU,ECAM and RMP)

edit
nope, it works...forget this post!

Hi JL and all simmers, yesterday i finally flyed with a double pc configuration.
On second pc (client) i had only stby instruments and EWD ad SD.
All is ok but my ECAM CockpitSonic panel was off and it didn't have iteration with software.
All others Cockpitsonic panels worked well.

Do you have any idea?

[jeehell]

What is the distribution if software and hardware over your computers?

[asessa]

What is the distribution if software and hardware over your computers?

All hw plugged on Server PC :
CockpitSonic FCU,RMP and ECAM
Skalarki MCDU
2 Saitek Throttles
1 Saitek Rudder
1 Trustmaster Hotas X

On the Server PC i had :
FGMS Server
WideFGMS Server
PFD, ND, OVH, MCDU CPT
Cockpitsonic, FSUIPC, Skalarki modules
EHID Drivers

On Client pc i had
EW/D, SD, Stby Instruments

How is the best scenario for you ?

[jeehell]

The distribution looks good. There is no reason the ECAM worked before and not anymore after networking, since it is all still plugged on the server.
The ecam application on the network is only a display, the hardware input is treated on the server computer no matter what (even when hardware is plugged in remote computer: the actions are sent to the server, treated, and the EIS then show what is required).

JL

[Leonidas]

Hi to all
Has anyone tried if there is an export format from PFPX that is compatible to JeeHell FMGS?
Regards

[Hikmat]

https://www.dropbox.com/s/1wo84zeducp28d6/IOS.7z?dl=0

Added some functions such as re-positions to the 3 and the 7 mile.s All airports are available

and ground acceleration test has been added (After full power select run test button) will be added comparison data also

best regards

Hikmat

[gurpalsc]

https://www.dropbox.com/s/1wo84zeducp28d6/IOS.7z?dl=0

Added some functions such as re-positions to the 3 and the 7 mile.s All airports are available

and ground acceleration test has been added (After full power select run test button) will be added comparison data also

best regards

Hikmat

dear hikmat,
i tried your software. and gace me an error.. lon 18.0090 etc not a valid floating point value.
i was in air when i run this software. or is there anything i missed to properly run this software?

[Hikmat]

dear hikmat,
i tried your software. and gace me an error.. lon 18.0090 etc not a valid floating point value.
i was in air when i run this software. or is there anything i missed to properly run this software?

Dear gurpalsc,

Make sure you have registered FSUIPC and r5, r4 are in same folder with the IOS. before reposition selecet an airport. Only Teke off 3ml and 7m repositions available

best regards

Hikmat

[gurpalsc]

Dear gurpalsc,

Make sure you have registered FSUIPC and r5, r4 are in same folder with the IOS. before reposition selecet an airport. Only Teke off 3ml and 7m repositions available

best regards

Hikmat

Dear Hikmat,
thanks... now it worked for the said dist. i.e., 7nm and 3 nm finals..
its indeed a nice software. hope to see more functions in it in future.
regards

[GoingForGold]

Could someone please tell me what already works concerning programmed restrictions in the MCDU?

Since the aircraft pretty much ignores everything, I wondered wheter I make mistakes or if its not implemented yet.

Thanks!