Results 1 to 5 of 5
  1. #1
    150+ Forum Groupie
    Join Date
    Oct 2006
    Location
    Perth, Australia
    Posts
    246
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    triplehead2go & Immersive display pro problem

    i'm hoping some1 has a solution to this problem.

    I'm trying to setup immersive display pro then run fsx WITHOUT having to change the display settings??

    Basically what is happening is I need to set projector 1 to configure immersive, I get it setup to a flyable state. I save the configuration. But then to get fsx on all 3 screens I need to change the display settings to start up on projector 2 the display works e.g blended

    Now when I restart w7 the blending has gone & needs re-aligning.... I have spoken to fly-elise & from that I think the cause is the desktop display is being changed.

    My question is how can I get fsx to display in all 3 projectors if I start it in projector 1? or get immersive to display in all 3 if started In projector 2?


    Thanks

    Michael
    A320 Home Simulator LHA435
    - FSX - i7 - GTX970 - Fly Elise - ASN -

  2. #2
    150+ Forum Groupie


    Miatanet's Avatar
    Join Date
    Dec 2011
    Location
    Switzerland
    Posts
    182
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Re: triplehead2go & Immersive display pro problem

    Hi Michel

    i guess you need to set up the 3 beamers or screens as one screen in windows, nvidia has a special setup for that if you are using nvidia, also the matrox driver should have this setting to make on 3x1 display...

    or dis i get you wrong?

    Best regards
    Stefan

    Another question from my site, I just board 2 equal beamers and using immersive display pro too, but i spend already about 4h to set up my beamers on my 180 degrees curved screen, but it messed up and i do not get this combiend. Do you have other tutorials availabel?

    BR
    Stefan

  3. #3
    2000+ Poster - Never Leaves the Sim


    OmniAtlas's Avatar
    Join Date
    Jun 2012
    Location
    Sydney, Australia
    Posts
    2,051
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Re: triplehead2go & Immersive display pro problem

    Have you tried the imme dive display pro auto configuration?
    Soarbywire - Airbus Flight Simulation and Engineering | Jeehell FMGS - Free professional A320 avionics software for the cockpit enthusiast.


  4. #4
    150+ Forum Groupie
    Join Date
    Oct 2006
    Location
    Perth, Australia
    Posts
    246
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Re: triplehead2go & Immersive display pro problem

    As always after I post a problem I resolve the issue

    Problem was the matrox manager was still showing 3 x displays where it should have been 1 !!!

    Stefan I used these tutorials; (I did mine manually)

    https://www.youtube.com/watch?v=wKDDAZChghs

    https://www.youtube.com/watch?v=yODUWFpY6io

    https://www.youtube.com/watch?v=YAQd_I76d7A (this 1 is different software but same principle)


    Michael
    A320 Home Simulator LHA435
    - FSX - i7 - GTX970 - Fly Elise - ASN -

  5. #5
    150+ Forum Groupie
    Join Date
    Oct 2006
    Location
    Perth, Australia
    Posts
    246
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Re: triplehead2go & Immersive display pro problem

    A320 Home Simulator LHA435
    - FSX - i7 - GTX970 - Fly Elise - ASN -