Fuel bug in Jeehell? (Usin with P3D)

[patrickk]

Hello there!
Yet another strange thing, that happens sometimes:
When I start Server and Client (client-PC just gives the graphical output for external displays), I sometimes do not have fuel on my Jeehell screens (ECAM). Strangely I have fuel in P3D "Fuel & Payload".

First I found out (somewhere in the www, please don't shot me, because I can't remember where), that this could happen if you do not start server first. So I always started the server first and client about 2 minutes later. Since yesterday this worked fine, but than there was it again. No fuel on the ECAM...

Did someone recognize the same Problem ever?
Every help would be appreciated. THANKS!

[jeehell]

Do you use teamviewer?

[patrickk]

No, actually the machines running the sim are not even connected to the internet. I had some issues with wifi, so I decided not to connect to the internet and have it as a closed network.

[jeehell]

do you use any addon which may change the fuel loading then?
Apart from that, I only can suspect a simconnect issue...

JL

[fisfro]

Hello ,

i have the same problem very often. Only new start of the server sw will bring fuell in the ecam. Changing of fuel in p3d will have no effect. I have a clean config without addons and without teamviewer. Everything else is working as expected...

Robert

[patrickk]

Hello ,

i have the same problem very often. Only new start of the server sw will bring fuell in the ecam. Changing of fuel in p3d will have no effect. I have a clean config without addons and without teamviewer. Everything else is working as expected...

Robert

Yes, seems to be the same problem I am getting. I can't figure out any reason which is causing it. And no JL, I also do not have any other software add ons installed.

Robert, are you doing just a server restart or do you need to shut down the hole machine and what is your setup like?

[fisfro]

l have to restart the server software without a shutdown of the flight server.
l'm also using P3d latest version with one client PC. No addons , no fsuipc etc, running . I'm using a clean flightserver pc with p3d, jeehell and warping software installed and a client pc with jeeheel installed- nothing else. Both systems are running with win8.1 and fds and cpflight hardware. Except of some crashes of the hardwareconnect task on the server and client pc jeeheel is running stable during flight (once you will have fuell on board .. ).

Robert

Robert

[phiberjenz]

Did you ever have any success in solving this problem? We have it all the time. Highly disturbing, as sometimes the fuel just disappears on ground. It could be enough that I go from window to full screen mode in P3D v 2.4.

// Jens

[spiliot]

It's a known issue that JL hasn't been able to figure out yet. While going on and off fullscreen is the most prominent way to see it manifest itself, there are other possible triggers like adding a printer, changing the taskbar autohide setting, etc. In fact all communication with FS is killed when that happens, the fuel is the easiest to spot on the ground, but try it in the air and SAR will be on its way

In B46 you could restart FSXConnect (with admin rights) and get the functionality back. Unfortunately that's not the case in B47 (at least for me).

[phiberjenz]

It's a known issue that JL hasn't been able to figure out yet. While going on and off fullscreen is the most prominent way to see it manifest itself, there are other possible triggers like adding a printer, changing the taskbar autohide setting, etc. In fact all communication with FS is killed when that happens, the fuel is the easiest to spot on the ground, but try it in the air and SAR will be on its way

In B46 you could restart FSXConnect (with admin rights) and get the functionality back. Unfortunately that's not the case in B47 (at least for me).

Thank you for confirming this! Though, restarting FSXConnect solved it for me in B47.1, other weird things happened instead like got MREV on the engines and could not control it with the thrust levers. Oh well, let's just don't switch between window and full screen for now