A320 FMGS B42/43

[Leonidas]

Leonidas: yes you need to reassign all axis to test that it may be the issue.... IIT.dnt is only for SW/LEDs for FDS boards. Axis are regular joysticks axis... It's not that long anyway...
JL

Sorry, you're right, that backup are AControls.cfg and joySW.cfg.
So, I can't even execute FMGS_Config.exe. It doesn't run (no message). Anyway, that update for Navigraph (Sept. 12) was so big (hundrends items downloaded) or something went wrong with update?
Best regards

*****Reedit********* Don't spend your time with this, I reinstalled it and it's OK.
Thanks a lot.

[jeehell]

Sorry, you're right, that backup are AControls.cfg and joySW.cfg.
So, I can't even execute FMGS_Config.exe. It doesn't run (no message). Anyway, that update for Navigraph (Sept. 12) was so big (hundrends items downloaded) or something went wrong with update?
Best regards

Clearly something went wrong in the updating process??
Start back from b42.0 install package and update again.

[SimStar001]

Hi JeeHell,

I just reinstalled all my computers and am facing a problem. How do I Setup the Skalarki Thrust Levers that are corrected to another computer? In Skalarki profiler they're working flawless.

If I open the Config Tool with FMGS running I get an error message. If I open it with FMGS closed, the config tool will not detect the THR LVRs (Skalarki Profiler shows "JeeHell A320 FMGS: no" because it is not connected to the Server).

What Software (P3D, WideFS, SkalarkiProfiler JH320 etc.) Needs to run and in what order, to make the THR LVRs be detected by the Config tool?

All Skalarki Hardware runs ok and works fine, except the THR LVRs - which I can't configure.

Regards

Hello Maddin,

in case TQ is connected to remote PC do it like this:

1. start remote and server PC
2. start FSX or P3D, or which one u ever use
3. start profiler on remote pc ( hope u settted levers up in profile before?)
4. start FMGSconfig.exe
5. run profile in Profiler on remote PC
6. now on server PC click in the field for TQ axe and move the lever to detect them

This is how it is working!


GL and HF....

Regards Marco

[OmniAtlas]

JL FMGS is now supported on the navigraph 1510 cycle -- https://www.navigraph.com/ViewNews.aspx?newsId=80

[SimStar001]

Hey JL,

i did set admin rights to all executeables on each PC.
Pls have a look to this video, there you can see how the levers work with new version.

https://www.facebook.com/ProjectA320



Regards Marco

[jeehell]

It looks as if the AP/FBW module is not connected to the FMGS server? Can you check that on FMGS Server window?

[romeow]

For a change something quite different!

I've noticed that A/THR can't hold selected or managed speed as soon as wind speed changes are too excessive. In this case N1 decreases and stays between 66 and 72% - not enough to maintain speed. The blue arc asks more thrust but it looks like the needle can't exceed the 70 %. So the aircraft constantly loses speed.

Do all of you know this "bug" or am I the only one? Is this a problem of JH's software, of FSX or of the weather engine? Any workaround?

Regards
René
BTW While cruising with calm winds (or no weather loaded) A/THR works perfectly.

[asessa]

Asessa: it's normal the MCDU shows that when you insert the DEP/ARR. After 30seconds of IRS alignement, the ALIGN IRS prompt will be displayed in INIT A page, then all should be able to work...


JL

Tnx for your response, i'll try if it's ok next time

[Pim van Vrijaldenhoven]

Hallo Jean-Luc,

Just doing a flight with the Navigraph database. I am missing the VOR, NDB, WPT and ARPT on the ND when selected by the EFIS. And yes, I copied the five .bin files to the NAVDATA folder on the ND PC.

Best regards,

--pim

[SimStar001]

It looks as if the AP/FBW module is not connected to the FMGS server? Can you check that on FMGS Server window?

Hi JL,

AP/FBW Module is connected...
Firewall off as well....


I started again Beta 41.2 and tested, and thrustlever working again....


Any Idea?