Results 1 to 5 of 5
  1. #1
    Our new friend needs to reach 10 posts to get to the next flight level
    Join Date
    Aug 2014
    Location
    Bangkok
    Posts
    6
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Cannot read value from JeeHell by fsuipc offset

    Hello everyone.
    This my first post.I have question about how to read value from JeeHell this difference from PMDG? Usually I use Link2fs for read offset to check value but I cannot read any value from offset JeeHell.What I do wrong? Need to config? Please advise to me.

    Thank you.

  2. #2
    Our new friend needs to reach 10 posts to get to the next flight level
    Join Date
    Aug 2014
    Location
    Bangkok
    Posts
    6
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Re: Cannot read value from JeeHell by fsuipc offset

    Quote Originally Posted by tonpp View Post
    Hello everyone.
    This my first post.I have question about how to read value from JeeHell this difference from PMDG? Usually I use Link2fs for read offset to check value but I cannot read any value from offset JeeHell.What I do wrong? Need to config? Please advise to me.

    Thank you.
    5-5-2558 16-41-40.jpg
    I try to open FSUIPC Connect this show "Not compatible with FSX/P3D......"

  3. #3
    2000+ Poster - Never Leaves the Sim


    OmniAtlas's Avatar
    Join Date
    Jun 2012
    Location
    Sydney, Australia
    Posts
    2,050
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Re: Cannot read value from JeeHell by fsuipc offset

    Did you run configure.exe (tick This computer is running FS9/X), and then StarterFSX.exe?
    Soarbywire - Airbus Flight Simulation and Engineering | Jeehell FMGS - Free professional A320 avionics software for the cockpit enthusiast.


  4. #4
    Our new friend needs to reach 10 posts to get to the next flight level
    Join Date
    Aug 2014
    Location
    Bangkok
    Posts
    6
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Re: Cannot read value from JeeHell by fsuipc offset

    Quote Originally Posted by OmniAtlas View Post
    Did you run configure.exe (tick This computer is running FS9/X), and then StarterFSX.exe?
    This my step after open computer
    1.Open MSFX and select JH A320.
    2.Go to C:\A320FMGS and open configure.exe and select This computer is running FS9/X.
    3.StarterFSX.exe
    4.Go to C:\A320FMGS\FMGS Server and open FSUIPCconnect.exe but same result.
    Is this correct step.

    Thank you JeeHell for your support.

  5. #5
    2000+ Poster - Never Leaves the Sim
    Join Date
    Mar 2008
    Location
    France,Nice
    Posts
    2,426
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Re: Cannot read value from JeeHell by fsuipc offset

    FSUIPCconnect is not used to have FSUIPC hardware controls. You must not use that with FSX/P3D
    You just have to install FSUIPC supprot during installation. Then, starterFSX will launch hardwareConnect which adds the FSUIPC support.


    regards,
    JL