Results 1 to 5 of 5

Thread: Leo Bodner

  1. 12-03-2014, 05:31 PM #1
    johnnyg
    johnnyg is offline
    75+ Posting Member
    Join Date
    Dec 2010
    Location
    Usa
    Posts
    102
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Leo Bodner

    what do you need to make the digits or lights change on a radio panel using a Leo Bodner BU0836X controller board and a segmented lighted display board? A wiring diagram and picture would also be helpful.
    Last edited by johnnyg; 12-03-2014 at 05:33 PM. Reason: more info
    Reply With Quote Reply With Quote
  2. 12-04-2014, 01:27 AM #2
    tiburon
    tiburon is offline
    300+ Forum Addict


    tiburon's Avatar
    Join Date
    May 2007
    Location
    Amsterdam
    Posts
    350
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Re: Leo Bodner

    You can't. The Bodnar controller is an input card, so it only connects switches and encoders.
    You will need an output card.
    This might help you along :

    http://www.flightsimparts.eu/Simulat..._7Segment.html

    Similar solutions are to be found at Opencockpits and other manufaturers.
    Gigabyte GA-Z97X - Intel i7 4790K@4,6 GHz - GSkill TridentX F3-2400C9D-8GTXD - 2 X Samsung 840 EVO 120GB - Seagate SSHD 2TB - Asus GTX780 DC2 OC 3GD5 - Windows 10 Professional 64
    Reply With Quote Reply With Quote
  3. 12-04-2014, 11:17 PM #3
    Westozy
    Westozy is offline
    MyCockpit Support Staff
    Builder Of The Month / Point Value: 100
    Total Awards: 1
    Total Points: 100



    Westozy's Avatar
    Join Date
    Nov 2005
    Location
    Perth, Western Australia
    Posts
    1,415
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Re: Leo Bodner

    Agreed, these are what I just fitted to my Landing and Cruise Alt displays in my FWD overhead - they work perfectly with Prosim! For radios I think you are better off buying them PnP!

    http://www.flightsimparts.eu/Simulat..._7Segment.html


    Cheers Gwyn
    Last edited by Westozy; 12-04-2014 at 11:29 PM.

    737NG using Prosim737, Immersive Calibration Pro, Aerosim Solutions motorized TQ & cockpit hardware, CP Flight MCP & FDS SYS1X, SYS2X & SYS4X, FDS PRO FMCs, AFDS units & Glarewings, Matrix Orbital ELEC display, Pokeys Landing & Cruise alt display, Buttkicker Gamers, 3 x BenqMW811ST projectors with a Matrox Th2Go
    http://www.aerosimsolutions.com.au
    Supporter of MyCockpit.org, please join me in donating!!!
    Reply With Quote Reply With Quote
  4. Post Thanks / Like - 1 Thanks, 0 Likes, 0 Dislikes
    Thanks Wendy thanked for this post
  5. 12-05-2014, 03:47 PM #4
    johnnyg
    johnnyg is offline
    75+ Posting Member
    Join Date
    Dec 2010
    Location
    Usa
    Posts
    102
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Re: Leo Bodner

    20141205_132647.jpgShould the LED displays move on the altitude display showing the altitude when you turn the encoder dial. here's how I wired it. It don't move what do I need to change to make the numbers change in the FSX 10 program. See Attached photo.
    Last edited by johnnyg; 12-06-2014 at 12:03 PM. Reason: pict
    Reply With Quote Reply With Quote
  6. 12-09-2014, 03:26 PM #5
    johnnyg
    johnnyg is offline
    75+ Posting Member
    Join Date
    Dec 2010
    Location
    Usa
    Posts
    102
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Re: Leo Bodner

    I got them to change thanks.
    Reply With Quote Reply With Quote
« Previous Thread | Next Thread »