A320 FMGS B36

[skalarki]

Hi Guys

All changes JL made in SkalarkiIO.dll are not tested by myself so far. I will do tests tomorrow and will give feedback.
To get all working new JLFMGS.dll will be needed (new version was only supplied to Filippo). Summarizing not all issues might come from JL, some might be from my side as well. Once I have tested all I will publish new SkalarkiIO Profiler as well as new .dll

Regards, Marcin

[buentead]

@fil:
I'm still using the SkalarkiIOProfiler 4.1[beta] and not the DLL you received from Marcin. I think this could be the problem. Hence, I'll wait until Marcin releases the next version.

@JL:
I'll postpone my B36.3 tests until Marcin releases next version of IOProfiler. Disregard my last reported B36.3 issues as the root cause might be somewhere else.

Nevertheless, the issue with the WideFMGS in B36.2 still exists. I'm using 2 clients connected to the WideFMGSServer. Many times the reconnect works. But occasionally I still get the Access Violation at address 004047B7 (writing to address 18B72000). Furthermore, if the client doesn't connect, then also one of the ports doesn't get reconnected, e.g. port 8004. But as said, it's occasional and hence, it's a minor issue for me.

Thank you all for your support
Adrian

[SSO]

Hi Jean Luc,

With the latest update my CockpitSonic RMP shows 122._80 instead of 122.800. It is however received by P3D and subsequently VATSIM vPilot as 122.800.
This was never a problem before. Goes for both Active and Standby.

/Stephen

[Tom_a330]

I am currently testing the new B36. I am using a touchsrcreen for the MCDUs. unfortunately the first RSK does not respond. I klick on it but it does not work. All other Buttons work. I am using the MCDU in the normal view (not "Display only").

Hi,

i finaly updated from 35.1 to 36.3 on friday but got the same problem. The first right key doesnt work which makes it impossible to align. Ive also seen that the PROG abd PERF pages show up some amber "display problem" display error.
Problem remained even after a complete new install of the entire system (windows, FSX, jeehell)
I am using the MCDU on the same system as fsx. only pfd/nd/ed and sd are on a neetwork system.
navdata is ok and the problem was gone after i "downgraded" back to 35.1

tomorrow ill try to run a separate 36.3 installation to see if i find any differences between 35 and 36.

cheers

tom

[jeehell]

@SSO: I'll check that.

@Tom: you MUST recalibrate the THR LVR axis in FMGS config.

JL

[SSO]

I also see in the WideFMGS on the server I get a MsgMutexMain1 time out.
Had a complete Error->disconnect of server port2.
Had to restart the client with OH+MCDU in-air which became quite interesting with both engines and APU being shut down...

Changed two network switchboxes earlier that were causing me problems so my LAN network is now top notch

[Tom_a330]

@Tom: you MUST recalibrate the THR LVR axis in FMGS config.

Could it be that simple? Yes it could. I tried again and this time i double checked that i did a 100% correct joystick calibration. Problem solved.....
Thanks again for your quick help.

cheers

Tom

[krosa]

Hi JL,

with the latest update also both my Tekworx radio display stopped working.I use them to change COM1 frequency.
If i turn the dial and press the button the frequency is correctly changed in the sim (P3Dv2) but the display are always off.
I already checked the display with the configuration software and they're not faulty.

Thank you

Stefano

[jeehell]

Stefano, I've just put an update, it should correct that.
regards,
JL

[janinp]

Hi JH
I just installed A320fmgs on a clean prepar3d for the first time. Pfd nd sd on network. I receive the same error message as Stephen : MsgMutexMain1 time out. As a result fuel is not updated from server PCA and remains at 0. There may be other information not updated. A few minutes after batteries on, a news message appeared for Fuel Lvr tank. Hope it is not to hard to solve. I am anxious to test prepar3d under windows 8.1.
Pierre