Results 1 to 2 of 2
  1. #1
    10+ Posting Member
    Join Date
    Oct 2013
    Location
    Germany
    Posts
    11
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Strange LED behavior

    Hi,

    I am quite a newbie in JeeHell in SIOC. That's the reason why I start step by step with my overheadpanel (AntiIce Panel) to build up a fixed based A320 (once upon...)

    I use:

    - OC USB Extention J1 <> OC MasterCard P1
    - OC USB Outputs <> Out 63 LED

    My first SIOC configuration was to get LED 63 lighted if APU Availible LED is on.

    That's my config:
    Code:
    // *****************************************************************************// * Config_SIOC ver 4.5   -     By Manuel Velez    -    www.opencockpits.com
    // *****************************************************************************
    // * FileName : sioc.txt
    // * Date : 09.10.2013
    
    
    
    
    
    
    Var 0001, name APUmasterSW, Link IOCARD_SW, Device 1, Input 1
    For testing I press:

    1) Both BAT switches at the Jeehell Overhead Panel (Software)
    2) APU Master Switch
    3) APU Start Switch

    After pressing APU Master Switch LED 63 is getting lighted and I don't understand why...
    After APU Start Switch is pressed LED 63 turned off until AVAIL is on (then LED 63 turns on again)...

    I am a bit confused.

    I changed allready LED 63 to another output to avoid a defective output but same behaviour with another output.

    My SIOC.INI:

    Code:
    [ fichero de configuracion para el SIOC ver. 4.5 ]
    [ Configuration file for SIOC ]
    
    
    
    
    [************** SIOC ***************]
    
    
    [ Nombre asignado al SIOC ]
    [ SIOC name ]
    Name=Main
    
    
    [ Puerto del servidor IOCP ]
    [ IOCP port ]
    IOCP_port=8092
    
    
    [ Tiempo de respuesta máximo de los paquetes IOCP ]
    [ IOCP Timeout ]
    IOCP_timeout=4000
    
    
    [ Arranque minimizado en la barra ]
    [ Start minimized in tray ] 
    Minimized=No
    
    
    [ Retraso necesario para las variables toggles (Project Magenta)]
    [ Deley needed for var. toggles (Project Magenta) ]
    toggle_delay=20
    
    
    [ Fichero de configuracion ]
    [ Configuration File ]
    CONFIG_FILE=.\JeeHellWare.ssi
    
    
    
    
    [************** MONITOR MODULE ***************]
    
    
    [ Desabilitar monitorizacion remota del SIOC ]
    [ Remote monitor disable mode yes/no ]
    Monitor_disable=No
    
    
    [ Refresco broadcast monitor (en segundos) ]
    [ Broadcast monitor time (seconds) ]
    Monitor_time=2
    
    
    
    
    [************** IOCARDS MODULE ***************]
    
    
    [ Desactivar el módulo de las IOCards ]
    [ Disable IOCards module ]
    IOCard_disable=No
    
    
    [ Divisor de frecuencia para los ejes analogicos (1-999). Retarda la entrega de valores. ]
    [ Frequency divisor for delay the analogic axes. (1-999)]
    Divisor_AD=10
    
    
    [------------- CARDS CONFIG -------------]
    
    
    [ IOCard Master ]
    [...............]
    
    
    [ Spanish : ]
    
    
    [ MASTER=(Indice device),(Tipo),(Número de tarjetas),(Número device) ]
    
    
    [ Indice Device: Índice usado en la variable SIOC como device, para indicar a que tarjeta se hace referencia ]
    [ Se usa 0 en el caso de que sólo haya una tarjeta y no se tenga en cuenta el número de device, por defecto un script en SIOC cuando no se pone parámetro DEVICE, se hace referencia al índice 0]
    
    
    [ tipo = 0 : Emulador de Master Card // OBSOLETO ]
    [ tipo = 1 : Tarjeta Master conectada al puerto paralelo directamente // OBSOLETO ]
    [ tipo = 2 : Tarjeta Master conectada al puerto paralelo mediante cable de compatibilidad // OBSOLETO ]
    [ tipo = 3 : Placa de expansión por puerto paralelo // OBSOLETO ]
    [ tipo = 4 : Tarjeta USBExpansion usada ]
    [ tipo = 5 : Modulo MCP de Opencockpits ]
    [ tipo = 6 : Tarjeta USBOutputs ]
    [ tipo = 7 : Modulo EFIS de Opencockpits ]
    [ tipo = 8 : Modulo Radio COM de Opencockpits ]
    [ tipo = 9 : Modulo Radio NAV de Opencockpits ]
    [ tipo = 10 : Modulo Radio ADF de Opencockpits ]
    [ tipo = 11 : Modulo Radio ATC de Opencockpits ]
    [ tipo = 12 : Modulo Radio Airbus RMP de Opencockpits ]
    [ tipo = 13 : Modulo FMC-737 de Opencockpits ]
    [ tipo = 14 : Tarjeta USBDcmotorPLUS ]
    [ tipo = 15 : Modulo MCP V3 de Opencockpits ]
    [ tipo = 16 : Modulo CRONOMETRO B737 ]
    
    
    
    
    [ Número de tarjetas = Número de placas Master usadas, 1 a 4 para uso de placas de expansión, 1 para conexión de placa Master directa o del Emulador ]
    
    
    [ Número de device = 0 en el caso del Emulador o primera tarjeta USB detectada, Dirección del puerto paralelo (por ejemplo $0378), o número de dispositivo USB ]
    
    
    
    
    [ Un ejemplo de 2 USBExpansion conectadas con 3 y 2 placas Master ]
    [ MASTER=0,4,3,22 ]
    [ MASTER=1,4,2,24 ]
    
    
    [ Un ejemplo de conexión a simulador ]
    [ MASTER=0,0,1,0 ]
    
    
    
    
    [ English : ]
    
    
    [ MASTER=(Device index),(Type),(Number of cards),(Device number) ]
    
    
    [ Device index : Index used in SIOC variable like device, this is the card used for SIOC sentence ]
    [ Use 0 for only one card, for this value you not need specify Device number. If you not use DEVICE parameter in a definition in SIOC script, the default index used is 0]
    
    
    [ type = 0 : Master Card Emulator // OBSOLETE ]
    [ type = 1 : Master Card connected directly to parallel port // OBSOLETE ]
    [ type = 2 : Master Card connected throught compatibility cable to parallel port //OBSOLETE]
    [ type = 3 : Expansion Card connected throught parallel port //OBSOLETE ]
    [ type = 4 : USBExpansion Card used ]
    [ type = 5 : Opencockpits MCP module ]
    [ type = 6 : USBOutputs Card used ]
    [ type = 7 : EFIS module ]
    [ type = 8 : Radio COM module ]
    [ type = 9 : Radio NAV module ]
    [ type = 10 : Radio ADF module ]
    [ type = 11 : Radio ATC module ]
    [ type = 12 : Radio RMP Airbus module ]
    [ type = 13 : FMC-737 module ]
    [ type = 14 : USBDCmotorPLUS Card used ]
    [ type = 15 : MCP V3 module ]
    [ type = 16 : CHRONO B737 module ]
    
    
    [ Number of Cards = Master cards connecteds, 1 to 4 for expansion cards, 1 for a Master card directly connected or Emulator ]
    
    
    [ Number of device = 0 for Emulator or first USB card detected, parallel port address, device number for specifies USBexpansion card ]
    
    
    [ For example, two USBExpansion cards connected with 3 and 2 Master cards used ]
    [ MASTER=0,4,3,22 ]
    [ MASTER=1,4,2,24 ]
    
    
    [ For example, use of Master card emulator ]
    [ MASTER=0,0,1,0 ]
    
    
    [ Use the first USBExpansion card connected with only one Master Card attached ]
    [ Esta definición es para usar la primera tarjeta USBExpansion que se encuentre instalada que además llevará conectada una placa Master ]
    
    
    [MASTER=3,6,1,252]
    [MASTER=0,4,1,0]
    [MASTER=0,12,1,0]
    [MASTER=0,16,1,0]
    
    
    [ Others Cards / Otras tarjetas ]
    [...............................]
    
    
    [ Spanish : ]
    
    
    [ Nombre_de_tarjeta=(Indice device),(Número device) ]
    
    
    [ Indice Device: Índice usado en la variable SIOC como device, para indicar a que tarjeta se hace referencia ]
    [ Se usa 0 en el caso de que sólo haya una tarjeta y no se tenga en cuenta el número de device, por defecto un script en SIOC cuando no se pone parámetro DEVICE, se hace referencia al índice 0]
    
    
    [ Número de device = 0 para usar primera tarjeta USB de este tipo detectada ó número de dispositivo USB ]
    
    
    
    
    [ English : ]
    
    
    [ Name_of_card=(Device index),(Device number) ]
    
    
    [ Device index : Index used in SIOC variable like device, this is the card used for SIOC sentence ]
    [ Use 0 for only one card, for this value you not need specify Device number. If you not use DEVICE parameter in a definition in SIOC script, the default index used is 0]
    
    
    [ Number of device = 0 for first USB card of this type detected, or device number for a specifies device ]
    
    
    [ Ejemplo de dos USBServos en indices 0 y 1, y números de devices 17 y 23 ]
    [ Example of two USBServos for index 0 and 1, and device number 17 and 23 ]
    
    
    [ USBServos=0,17 ]
    [ USBServos=1,23 ]
    
    
    
    
    [USBStepper=0,0]
    [USBKeys=0,0]
    [USBServos=0,0]
    [USBRelays=0,0]
    [USBDCmotor=0,0]
    
    
    [ Para los ejes analógicos se usan los números de devices de las tarjetas donde están alojados ]
    [ For analogic axles, you use the device number of cards what allow the axles ]
    
    
    [USBAnalogic=0,0]
    
    
    
    
    [************** FSUIPC MODULE ***************]
    
    
    [ Desabilitar lectura de las FSUIPC ]
    [ FSUIPC disable mode yes/no ]
    FSUipcdisable=No
    
    
    [ Refresco recepción FSUIPC ]
    [ FSUIPC refresh ]
    FSUipcRefresh=50
    
    
    
    
    [************** IOCP CLIENTS MODULES ***************]
    
    
    [ Retraso para inicializacion una vez conectado el cliente en milisegundos ]
    [ Delay for initialization when client has been connected in mseconds ]
    IOCPini_delay=3000
    
    
    [************** IOCP CLIENT MODULE #0 ***************]
    
    
    [ Desactivar el módulo cliente IOCP ]
    [ Disable IOCP client module ] 
    IOCPclient0_disable=No
    
    
    [ IP del servidor donde debe de conectar el cliente ]
    [ IOCP client host name ]
    IOCPclient0_host=localhost
    
    
    [ Puerto de envio del protocolo IOCP cliente ]
    [ IOCP client port ]
    IOCPclient0_port=8099
    
    
    
    
    [************** IOCP CLIENT MODULE #1 ***************]
    
    
    [ Desactivar el módulo cliente IOCP ]
    [ Disable IOCP client module ] 
    IOCPclient1_disable=yes
    
    
    [ IP del servidor donde debe de conectar el cliente ]
    [ IOCP client host name ]
    IOCPclient1_host=localhost
    
    
    [ Puerto de envio del protocolo IOCP cliente ]
    [ IOCP client port ]
    IOCPclient1_port=8099
    
    
    
    
    [************** SOUND MODULE ***************]
    
    
    [ Ficheros de sonido ]
    [ Sound Files ]
    
    
    [ Desactivar el módulo de sonido ]
    [ Disable Sound module ]
    Sound_disable=yes
    
    
    [ Volumen general de los sonidos 0-100 ]
    [ Master Volume 0-100 ]
    Volume=100
    
    
    
    
    [ put '*' first filename for loop Sound ]
    [ anteponer '*' en el fichero para bucle continuo de sonido]
    
    
    [ Sound=wav_file,frequency,volume,pan ]
    [ frequency=100 to 100000 0=original -1=current ]
    [ volume=0 to 100, -1=current ]
    [ pan=-100 (left) to +100 (right) 0=center -1=current ]
    
    
    [ Sound=Fichero_wav,frecuencia,volumen,balance ]
    [ frecuencia=100 hasta 100000 0=original -1=Por defecto ]
    [ volumen=0 hasta 100 -1=Volumen por defecto ]
    [ balance=-100 (Izquierda) hasta +100 (Derecha) 0=centro -1=Por defecto ]
    
    
    [ #1 ]
    Sound=APDis.wav,-1,-1,-1
    
    
    [ #2 ]
    Sound=*outermk.wav,-1,-1,-1
    
    
    [ #3 ]
    Sound=*hello.wav
    
    
    [************** KEYBOARD EMULATOR MODULE ***************]
    
    
    [ Nombre exacto de la ventana donde se enviarán las teclas ]
    [ Name of window for key send ]
    [window = "Project Magenta Glass Cockpit - Build 396" ]
    
    
    window =a.txt - Bloc de notas 
    
    
    
    
    [ Asignación de teclas ]
    [ assign youe keys ]
    
    
    #1=A
    #2=B
    #3=C
    #4=D
    #5=E
    #6=F
    #7=G
    #8=H
    #9=I
    #10=J
    #11=K
    #12=L
    #13=M
    #14=N
    #15=O
    #16=P
    #17=Q
    #18=R
    #19=S
    #20=T
    #21=U
    #22=V
    #23=W
    #24=X
    #25=Y
    #26=Z
    #27=1
    #28=2
    #29=3
    #30=4
    #31=5
    #32=6
    #33=7
    #34=8
    #35=9
    #36=0
    #37=<
    #38=,
    #39=.
    #40=-
    #41=*
    #42=+
    #43=//
    #44=/0
    #45=/1
    #46=/A
    #47=
    #48=
    #49=
    #50=
    #51=
    #52=
    #53=
    #54=
    #55=
    #56=
    #57=
    #58=
    #59=
    #60=
    #61=
    #62=
    #63=
    #64=
    #65=
    #66=
    #67=
    #68=
    #69=
    #70=
    #71=
    #72=
    #73=
    #74=
    #75=
    #76=
    #77=
    #78=
    #79=
    #80=
    #81=
    #82=
    #83=
    #84=
    #85=
    #86=
    #87=
    #88=<a
    #200=B
    
    
    
    
    [ --- SIOC Autoconfig Devices Ver 4.5B1 ==> 09.10.2013 06:05:00 <== ----]
    MASTER=1,4,1,11
    MASTER=0,6,1,5
    Would be nice if you can light up my brain... ;O)

    Regards,
    pero

  2. #2
    2000+ Poster - Never Leaves the Sim
    Join Date
    Mar 2008
    Location
    France,Nice
    Posts
    2,426
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Re: Strange LED behavior

    Hi,

    Although it is possible to create your complete SIOC script to retrieve LEDs state, the best way with SIOC is to use the little software included in my suite, called SIOCcreator. You'll find it in hardware modules folder (you must have selected SIOC support during installation).

    Regards,
    JL