Results 1 to 9 of 9
  1. #1
    300+ Forum Addict manhattan's Avatar
    Join Date
    Nov 2007
    Location
    Plymouth UK
    Posts
    346
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    THROTTLE QUADRANT QUESTIONS

    Hi Gwyn.

    I am putting together a 737 cockpit, but having only ever flown a Twin Otter, I am having to learn a few new things!
    Could you explain how the trim wheels interface with FS? They appear to have almost unlimited turns and I can't see how this motion is transferred to a 'trim up' 'trim down' action?

    Hope you can help!

    Regards,


    TONY Plymouth UK

  2. #2
    300+ Forum Addict


    tiburon's Avatar
    Join Date
    May 2007
    Location
    Amsterdam
    Posts
    350
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Re: THROTTLE QUADRANT QUESTIONS

    I don't know if anybody has actually interfaced the trim wheels themselves since trim is applied through a switch on the yoke. In real life you could trim the elevator by turning the wheel but it would be very tedious.

  3. Dislikes nico737200 disliked this post
  4. #3
    25+ Posting Member jsfboat's Avatar
    Join Date
    Jan 2010
    Location
    Sebastian, Florida
    Posts
    54
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Re: THROTTLE QUADRANT QUESTIONS

    On the B1900s I was flying, there is both electrical trim, via yoke switches, and also a trim wheel next to the throttle quadrant. The idea was to use the electrical trim to get the trim close, then use the wheel to fine tune it. In the airplane I'm flying now, there is only electrical trim via the yoke, can't fine adjust the trim which is sometimes annoying, always try for the "let go and see what it does" method. I sometimes miss the old Beech. Why not get the Syteck Cessna trim wheel and modify that?

  5. #4
    300+ Forum Addict Avro748's Avatar
    Join Date
    Dec 2012
    Location
    At the Controls
    Posts
    347
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Re: THROTTLE QUADRANT QUESTIONS

    I found this on Bodnar's site:
    Infinite Potentiometer

  6. #5
    150+ Forum Groupie



    Join Date
    Dec 2011
    Location
    Canada
    Posts
    175
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Re: THROTTLE QUADRANT QUESTIONS

    Quote Originally Posted by manhattan View Post
    Hi Gwyn.

    I am putting together a 737 cockpit, but having only ever flown a Twin Otter, I am having to learn a few new things!
    Could you explain how the trim wheels interface with FS? They appear to have almost unlimited turns and I can't see how this motion is transferred to a 'trim up' 'trim down' action?

    Hope you can help!

    Regards,


    TONY Plymouth UK

    Hi Tony,

    I interfaced my trim wheels using pulse switches. You can find info on the pulse switches on Ian's site. Ordered mine from Mouser.. 3 or 4 dollars each or something like. I didn't like the idea of having the trim wheels there as an ornament..so interfaced them each to a pulse switch and FSUIPC. They work great and it's an easy mod. The only thing I dont have is a graduation needle to show where the trim is at, but Prosim has a scale that can be dragged and dropped in a convenient location for viewing.

  7. #6
    MyCockpit Support Staff


    Westozy's Avatar
    Join Date
    Nov 2005
    Location
    Perth, Western Australia
    Posts
    1,415
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Re: THROTTLE QUADRANT QUESTIONS

    Wow I am late on seeing this one, sorry Tony!
    The way I have built my TQ's trim system - I have it on good authority that there are 45 turns "lock to lock" on the trim wheels of the Boeing TQ so I built in a reduction drive to drive a gear on which the trim indicators are mounted on. 45 turns of my trim wheels move the trim indicators along the scales which is about 65mm long. This movement is only about 50 degrees of rotation but the indicator gear and this gear also drives my trim potentiometer so all up, 45 turns of the trim wheels turn my trim pot 270 degrees, what a challenge that was to achieve!! When I trim on the yoke buttons the value will change in FS instantly. The FS trim value is transmitted to a Phidgets DC motor controller card which is reading my trim pot value. A DC motor will then rotate the trim wheels until all the values align. The custom software has acceleration and deceleration functions built in so it shouldn't hunt or mess about. We have proven it for driving the auto throttles on another TQ that I built, it works great but we have tested on the trim function as yet because my TQ is not yet wired up. My software engineer Thomas assures me it this is all "too easy" and simple to achieve. I will report more on this when it is finally assembled.

    If you just want to achieve manual trim with unlimited turns on the trim wheels, make them rotate a rotary encoder should do the trick but the electronics guys would need to describe that one for you...

    Cheers Gwyn

    737NG using Prosim737, Immersive Calibration Pro, Aerosim Solutions motorized TQ & cockpit hardware, CP Flight MCP & FDS SYS1X, SYS2X & SYS4X, FDS PRO FMCs, AFDS units & Glarewings, Matrix Orbital ELEC display, Pokeys Landing & Cruise alt display, Buttkicker Gamers, 3 x BenqMW811ST projectors with a Matrox Th2Go
    http://www.aerosimsolutions.com.au
    Supporter of MyCockpit.org, please join me in donating!!!

  8. Likes jeanlou liked this post
  9. #7
    New Member
    Join Date
    Jul 2015
    Location
    reunion island
    Posts
    3
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Re: THROTTLE QUADRANT QUESTIONS

    Hi Gwyn.

    Great job for your trim wheel.
    I'm working on my 737 TQ and I have motorised the handles by servo motor with Link2fs program and an arduino Uno. Now I must motorise my trim wheel like you with dc motor and I would like to know which script did you used for that.
    Thanks a lot for your reply.

    Jean-lou

    Reunion Island

  10. #8
    MyCockpit Support Staff


    Westozy's Avatar
    Join Date
    Nov 2005
    Location
    Perth, Western Australia
    Posts
    1,415
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Re: THROTTLE QUADRANT QUESTIONS

    Hi Jean,
    My custom C Sharp script was written by my Worldflight crew member and good friend Thomas. I don't really know how it works but basically it is designed to make the trim wheel indicators follow and match the Prosim trim gauge. When I trigger the yoke trim, the Prosim gauge moves and my wheels spin to move the TQ indicator. This indicator has a feedback pot and it is basically a loop control. Moving my trim wheels by hand does not trim the plane. The wheels spin and adjust all the time when the auto pilot is on, it is very cool but I can't help you with software or code unfortunately. Cheers Gwyn

    737NG using Prosim737, Immersive Calibration Pro, Aerosim Solutions motorized TQ & cockpit hardware, CP Flight MCP & FDS SYS1X, SYS2X & SYS4X, FDS PRO FMCs, AFDS units & Glarewings, Matrix Orbital ELEC display, Pokeys Landing & Cruise alt display, Buttkicker Gamers, 3 x BenqMW811ST projectors with a Matrox Th2Go
    http://www.aerosimsolutions.com.au
    Supporter of MyCockpit.org, please join me in donating!!!

  11. #9
    New Member
    Join Date
    Jul 2015
    Location
    reunion island
    Posts
    3
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Re: THROTTLE QUADRANT QUESTIONS

    Quote Originally Posted by Westozy View Post
    Hi Jean,
    My custom C Sharp script was written by my Worldflight crew member and good friend Thomas. I don't really know how it works but basically it is designed to make the trim wheel indicators follow and match the Prosim trim gauge. When I trigger the yoke trim, the Prosim gauge moves and my wheels spin to move the TQ indicator. This indicator has a feedback pot and it is basically a loop control. Moving my trim wheels by hand does not trim the plane. The wheels spin and adjust all the time when the auto pilot is on, it is very cool but I can't help you with software or code unfortunately. Cheers Gwyn
    Cheers Gwyn,

    My apologies for my late reply, some prb with my internet.
    Thanks for your reply. They made a great job for you, you are very lucky
    I need a script for the TRIM wheel wich will work with my arduino card because I use LINKE2FS to run all of my throttle quadrant.
    I use DC motor and if you have any informations on my script so tell me please
    May be you can give me any contacts who could help me on my script...

    here my script :

    #include
    Servo autotServo; // servo for my engine throttle 1
    Servo autotServo2; // servo for my engine throttle 2
    Servo autotServo3; // servo for my spoiler
    int Data;
    String AT;
    int pos = 0; // variable to store the servo position


    byte pinLed = 13; // LED for my parking brake




    void setup() {
    autotServo.attach(10); // KIOSHO
    autotServo2.attach(9); // POWER HD
    autotServo3.attach(6);
    Serial.begin(115200);
    Serial.flush();
    Serial.println("W");
    Serial.println("V");
    Serial.println("q");
    Serial.println("j");
    pinMode(13,OUTPUT);


    }

    void loop() {
    if (Serial.available() > 0) {
    Data = Serial.read();
    if (Data == 'W'){
    delay (1);
    AT = "";
    AT += char(Serial.read());
    AT += char(Serial.read());
    AT += char(Serial.read());
    AT += char(Serial.read());
    int ATInt = AT.toInt(); // convert it to an integer
    ATInt = (ATInt + 0);// Manual correction to suit servo zero.
    ATInt = map(ATInt, +0, +100, 28, 120);//map the integer
    for(pos =0; pos <180; pos += 1) // goes from 0 degrees to 180 degrees
    autotServo.write(ATInt);
    }//end of found "W"

    if (Data == 'V'){
    delay (1);
    AT = "";
    AT += char(Serial.read());
    AT += char(Serial.read());
    AT += char(Serial.read());
    AT += char(Serial.read());
    int ATInt = AT.toInt(); // convert it to an integer
    ATInt = (ATInt + 0);// Manual correction to suit servo zero.
    ATInt = map(ATInt, +0, +100,61, 119);//map the integer
    for(pos = 0; pos < 180; pos += 1) // goes from 0 degrees to 180 degrees
    autotServo2.write(ATInt);
    }//end of found "V"

    if (Data == 'q') {
    delay (1);
    AT = "";
    AT += char(Serial.read());
    int ATInt = AT.toInt();
    if (ATInt > 0) digitalWrite(pinLed, HIGH);
    else digitalWrite(pinLed, LOW);
    }

    if (Data == 'j') {
    delay (1);
    AT = "";
    AT += char(Serial.read());
    int ATInt = AT.toInt();
    if (ATInt > 0) autotServo3.write(90);
    else autotServo3.write(0);
    }


    }//end of serial read
    }//


    Everything work well, I'm very happy but my last step is the trim wheel...
    So keep me notified if you have any contact for me
    thanks a lot..

    kind regards