Page 1 of 2 12 LastLast
Results 1 to 10 of 12
  1. #1
    150+ Forum Groupie
    Join Date
    Dec 2010
    Location
    CUPAR FIFE SCOTLAND NEAR ST ANDREWS
    Posts
    163
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    eicas monitor panel for MIP

    Hi
    i would be very grateful for any help on this subject
    i am making my own mip which will consist of 3 panels,PFD L/H,EICAS AND PFD R/H
    my question is as follows -i will be using a 19 inch monitor behind the PFD L/H AND R/H
    but in the midle eicas panel i will be using 3 real standby guages (737)you know down the l/h side
    of this panel which means i cant use a 17 inch monitor but one much smaller as just above it will be the flap
    guage -has any one encountered this as i have looked on ebay and other sites for a small monitor to fit
    but they all seem to be either too small or too large -basically has any one built a mip using real standby guages -if so could you please tell me what type of monitor was used for the midle of the MIP
    many thanks
    dave

  2. #2
    500+ This must be a daytime job


    Efe Cem Elci's Avatar
    Join Date
    Jan 2008
    Location
    Istanbul, Turkey, Turkey
    Posts
    544
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Re: eicas monitor panel for MIP

    Like a square 15" monitor?

  3. #3
    150+ Forum Groupie
    Join Date
    Dec 2010
    Location
    CUPAR FIFE SCOTLAND NEAR ST ANDREWS
    Posts
    163
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Re: eicas monitor panel for MIP

    Hi efe
    15 inches would be too wide I have 9.5 inches from the
    Back of the real gauges on the left to the back of the flap lever on the right
    The 9.5 inches would have to be the total width of the monitor
    I wouldn't have to worry about the length as it would be hidden at the bottom of the centre of my mip frame
    Thanks for your reply
    And have a good day
    Dave

  4. #4
    500+ This must be a daytime job
    Join Date
    Jul 2013
    Posts
    948
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Re: eicas monitor panel for MIP

    Dave

    A 12 inch 4/3 ratio screen would fit. I got one off ebay with a screen size of 7.5" x 9.5" and an overall frame size of 13" x 9" No known make and ex POS equipmnet, but should give you a guide.

    David

  5. #5
    150+ Forum Groupie
    Join Date
    Dec 2010
    Location
    CUPAR FIFE SCOTLAND NEAR ST ANDREWS
    Posts
    163
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Re: eicas monitor panel for MIP

    Many thanks for that fordgt40
    I will have a look on eBay tonight
    Cheers
    Dave

  6. #6
    150+ Forum Groupie
    Join Date
    Apr 2007
    Location
    N/A
    Posts
    211
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Re: eicas monitor panel for MIP

    simparts.de might have something. Also look into digital picture frames. Some of them has video in...

  7. #7
    500+ This must be a daytime job


    Efe Cem Elci's Avatar
    Join Date
    Jan 2008
    Location
    Istanbul, Turkey, Turkey
    Posts
    544
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Re: eicas monitor panel for MIP

    Well that's tight. 15 inch square monitors have a 10.6 inch edge measurement so I thought that might work. Apparently not for your case. So a smaller monitor is in order.

  8. #8
    150+ Forum Groupie
    Join Date
    Dec 2010
    Location
    CUPAR FIFE SCOTLAND NEAR ST ANDREWS
    Posts
    163
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Re: eicas monitor panel for MIP

    Thank you I will look at sim parts de

  9. #9
    150+ Forum Groupie
    Join Date
    Dec 2010
    Location
    CUPAR FIFE SCOTLAND NEAR ST ANDREWS
    Posts
    163
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Re: eicas monitor panel for MIP

    Many thanks flying fox this looks like the way to go
    Thank you
    Dave

  10. #10
    150+ Forum Groupie
    Join Date
    Dec 2010
    Location
    CUPAR FIFE SCOTLAND NEAR ST ANDREWS
    Posts
    163
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Re: eicas monitor panel for MIP

    No problem efe it looks like flying fox
    Has solved my problem
    Thanks for trying
    Cheers
    Dave

Page 1 of 2 12 LastLast

Tags for this Thread