Results 1 to 10 of 16
-
07-23-2011, 04:24 PM #1
- Join Date
- Jul 2010
- Location
- Tulsa ok
- Posts
- 26
How to wire a rotary switch with Leo bu0836x board
Does any one know how to wire a rotary switch using a BU0836x board. I am trying to set up a some switches for 737sim panels. Any advise would help Thanks
Tony
-
07-23-2011, 11:38 PM #2
- Join Date
- Oct 2009
- Location
- Juneau, AK
- Posts
- 553
Re: How to wire a rotary switch with Leo bu0836x board
Rotary switch or rotary encoder?
Reidhttp://juneaucessnasim.blogspot.com
N58243 (virtual)- Low and Slow...
-
07-24-2011, 10:25 AM #3
Re: How to wire a rotary switch with Leo bu0836x board
If it's a single pole rotary switch like this one;
The centre pole is the ground. You would wire it and one of the switch poles to the ground and 5v switch input on the Bodnar board, every other switch pole would be wired to an individual 5v input and would share the common ground. With FSUIPC you can assign individual switch assignments to each position. Hope that made sense.
-
07-24-2011, 11:00 AM #4
- Join Date
- Jul 2010
- Location
- Tulsa ok
- Posts
- 26
-
08-07-2011, 02:29 PM #5
- Join Date
- Jun 2009
- Location
- Leuven, Belgium
- Posts
- 30
Re: How to wire a rotary switch with Leo bu0836x board
Hi, stupid question: how does one share a common on the BU0836X ?
Do I plug in little wires and jump from common to common in series?
-
10-24-2011, 02:24 PM #6
- Join Date
- Nov 2009
- Location
- Germany
- Posts
- 60
Re: How to wire a rotary switch with Leo bu0836x board
Hello,
i want to take up the question of fly_ebos again.....
How do i share a common ground on the BU Card ? I try to connect a rotary switch (no encoder) and want to connect the middle pin as shared GND for 2 switch positions.../GND B15 and GND B16 together, B15 one switch posistion; B16 one switch position). Only B15 Position works, when i try to switch B16 i get strange behaviour... I tried to use diodes but no change.
Any help appreciated.
Cheers
Andy
-
10-24-2011, 02:27 PM #7
- Join Date
- Jun 2009
- Location
- Leuven, Belgium
- Posts
- 30
Re: How to wire a rotary switch with Leo bu0836x board
I think I can answer this one myself: the Bodnar card has a common ground. You just have to make sure that you share the ground on the inputs/rotaries and then connect the input wires onto the Bodnard card.
-
10-24-2011, 02:32 PM #8
- Join Date
- Nov 2009
- Location
- Germany
- Posts
- 60
Re: How to wire a rotary switch with Leo bu0836x board
Hi,
ok, where can i find the common ground on the BU card ??
So i wired...
Center PIN of Rotary to common GND on Bu Card - where ?
Rotary Switch Pin 1 to B15 Output on Bodnar Card
Rotary Switch Pin 2 stays empty
Rotary Switch Pin 3 to B16 Output on Bodnar Card
Sorry for a lot of editing this post....
Cheers Andy
-
10-24-2011, 05:29 PM #9
Re: How to wire a rotary switch with Leo bu0836x board
The ground on the switch is common to all the outputs on the switch. There isn't a ground labelled "common" on the Bodnar board, all you need to do is run a wire from the ground on the switch to either ground input on the B15 and B16 card. As long as the ground is "common" on the switch, all the ouputs of the switch will use it.
-
10-24-2011, 08:14 PM #10
- Join Date
- May 2011
- Location
- Melbourne Australia
- Posts
- 32
Re: How to wire a rotary switch with Leo bu0836x board
Hi Tony,
Also check out this link.. Ian was a great help when I asked the same question a few months ago.
http://www.737ng.co.uk/rotaryaspot.pdf
Even though it explains the set up for wipers the same can be used for autobrake.
Hope this helps.
Cheers
Mark
Take a step towards your dream - participate and win!
Run-Time Check # 0 - The value of...