Results 1 to 9 of 9
  1. #1
    500+ This must be a daytime job Boeing 747 Flyer's Avatar
    Join Date
    Nov 2009
    Location
    England
    Posts
    771
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Dimensions for... (B767 forward panel)

    Hi everyone,

    I am wondering if anyone can give me any dimensions for the following part of the Boeing 767-200 aircraft:



    I appreciate the red pen covers it up a little, so here is the original:



    Thank you very much. Please note, I am not looking for MIP dimensions as a whole, just that little bit. I'm planning on constructing it in three phases, you see.

    Jack

  2. #2
    500+ This must be a daytime job
    Join Date
    Jul 2013
    Posts
    948
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site


  3. Thanks Boeing 747 Flyer thanked for this post
  4. #3
    500+ This must be a daytime job Boeing 747 Flyer's Avatar
    Join Date
    Nov 2009
    Location
    England
    Posts
    771
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Re: Dimensions for... (B767 forward panel)

    David,

    Please can you direct me to this "photo section"? I have checked the photo gallery on the site, and cannot find those specific photos mentioned in your post.

    Regards,

    Jack

  5. #4
    500+ This must be a daytime job
    Join Date
    Jul 2013
    Posts
    948
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Re: Dimensions for... (B767 forward panel)

    Jack

    It is not my post, just a link

    The major bit of info that I thought would help you were the photos with dimensions on the external site referenced on the first link and directly on the second

    I did not follow through re the photo section - thought the second link answered your original question.

    Regards

    David

  6. #5
    500+ This must be a daytime job Boeing 747 Flyer's Avatar
    Join Date
    Nov 2009
    Location
    England
    Posts
    771
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Re: Dimensions for... (B767 forward panel)

    Hi David,

    I had a few problems following the dimensions on the second link. Some of the photos are extremely blurry, and the part I want is split up into about 5 photographs, which are not aligned.

    Also, the tape-measure is not being held in flat-parallel to the panel, so it is difficult to read.

    Jack

  7. #6
    500+ This must be a daytime job
    Join Date
    Jul 2013
    Posts
    948
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Re: Dimensions for... (B767 forward panel)

    Jack

    Ok, sorry that it does not suit your needs

    David

  8. #7
    500+ This must be a daytime job Boeing 747 Flyer's Avatar
    Join Date
    Nov 2009
    Location
    England
    Posts
    771
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Re: Dimensions for... (B767 forward panel)

    Does anybody know of a different site with 767 dimensions?

    Regards,

    Jack

  9. #8
    150+ Forum Groupie twisted8's Avatar
    Join Date
    Jun 2009
    Location
    California
    Posts
    243
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Re: Dimensions for... (B767 forward panel)

    Check out this website
    he has a corel files with close dimensions. He can't confirm they are exact but it should be close enough

    http://www.hoddo.net/download.html

    hope that helps

  10. Thanks Boeing 747 Flyer thanked for this post
  11. #9
    500+ This must be a daytime job Boeing 747 Flyer's Avatar
    Join Date
    Nov 2009
    Location
    England
    Posts
    771
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Re: Dimensions for... (B767 forward panel)

    Quote Originally Posted by twisted8 View Post
    Check out this website
    he has a corel files with close dimensions. He can't confirm they are exact but it should be close enough

    http://www.hoddo.net/download.html

    hope that helps
    Hi Fabian,

    Thanks so much for that. I shall definitely using these dimensions.

    Jack