Results 1 to 5 of 5
  1. #1
    300+ Forum Addict
    Join Date
    Feb 2006
    Location
    N/A
    Posts
    458
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    SIOC Code for Elevator Trim, OC USBDCMotors, Project Magenta

    Has anyone setup the elevator trim wheel using SIOC, OC USBDC Motors Card and Project Magenta? If so, would you mind sharing your SIOC code please?

    Thank you

  2. #2
    500+ This must be a daytime job



    Join Date
    Jul 2013
    Posts
    917
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Re: SIOC Code for Elevator Trim, OC USBDCMotors, Project Magenta

    Hi

    Here is an example that I had in my "library". Thanks and credits to Manolo Velez and Herman Hummer. Do not know if it works, but should give you a start

    David





    Code:
    // *****************************************************************************
    // * Config_SIOC ver 3.5   -     By Manolo Vélez    -    www.opencockpits.com
    // *****************************************************************************
    // 
    // * Editor: Hermann Hummer www.simhard.eu.tt
    // 
    // * FileName : Motorized_Throttle_1.385.txt
    // * Date : 8.3.2008
    
    // * PM + PSS Airbus updated
    // * some variables shiftet
    // * manual Trim enabled when all AP of PM are disengaged
    // * Subroutine for motor movement starts every 50ms now 
    // * Some improvements for AP: eg. when APP is active then V/S is set to -2000
    // * PMDG variables changed esp. ALT-HOLD and SPEED-HOLD
    // * Pause modus is now dedected, so levers and trim stops in pause mode
    // * FeelThereAirbus with relais to connect levers to game port
    // * 2nd Mastercard and some inputs added for EFIS
    // * FSX Compatibility: Disconnect both LeverPotentiometers from FS when AP is on
    // * Variables for AIR-File different in FS9 and FSX
    // * Some improvements for LevelD FS9 & FSX
    // * FeelThere Airbus and FeelThere Boeing are recognised as different planes now
    // * VNAV sets IAS for LevelD
    // * Standard-AP OFF switches to Trim by Hand (eg. for FeelThere Airbus)
    // * LeverStart for FSX:  Var 12 & 13 changed Why different to FS9 ???? FSUIPC ??
    
     
    Var 1000, Value 0     // Initialisation
    
    
    {
    &Lever_Elevator = TIMER 999 , 0,5 // Subroutine for Lever and Elevator Motors starts every 50ms
    }
    
    
    Var 0004, name V1_385  // Version number
    
    Var 0000, name lever2_motor  // Motor control  
    
    Var 0001, name lever1_motor, value 1 // starts program
    
    Var 0002, name elevator_motor  // Motor control
    
    
    // for FeelThereAirbus only
    
    Var 0003, name Relais  // Relais switches from upper to lower printed board
    
    
    // The following variables depend on the used Potentiometers
    // You must check these values by using IOCPConsole for each Potentiometer
    // 1)for 100 percent thrust: 'LeverX_upper'  2)idle: 'LeverX_idle' 3)reverser: 'LeverX_lower'.
    // In this case the potentiometer values are the following:
    
    Var 0100, name Lever1_upper, Value 121  			// Upper potentiometer value of Lever1
    Var 0101, name Lever2_upper, Value 124  			// Upper potentiometer value of Lever2
    Var 0102, name Lever1_idle, Value 23  			// Idle potentiometer value of Lever1
    Var 0103, name Lever2_idle, Value 24  			// Idle potentiometer value of Lever2
    Var 0104, name Lever1_lower, Value 6  			// Lower potentiometer value of Lever1
    Var 0105, name Lever2_lower, Value 6   			// Lower potentiometer value of Lever2
    
    // Airbus only:
    Var 0106, name Lever1_CL, Value 65  			// CL potentiometer value of Lever1
    Var 0107, name Lever2_CL, Value 68   			// CL potentiometer value of Lever2
    Var 0108, name Lever1_FLX, Value 90  			// FLX potentiometer value of Lever1
    Var 0109, name Lever2_FLX, Value 93   			// FLX potentiometer value of Lever2
    
    Var 0014, name dead_area1     				// to avoid jitter, we define a 'dead area' for the potentiometers
    Var 0015, name break_dist1      				// how many points we need for break the motors to zero
    Var 0016, name current_break1   				// we can define a break current for the motor
    Var 0017, name current_run1     				// Speed for motor when running
    Var 0034, name dead_area2        
    Var 0035, name break_dist2     
    Var 0036, name current_break2     
    Var 0037, name current_run2
    
    Var 0041, name dead_area3, Value 8     
    Var 0042, name break_dist3, Value 30     
    Var 0043, name current_break3, Value 40     
    Var 0044, name current_run3, Value 50     		// Speed for motor when big difference
    
    
    
    Var 0110, name Lever1_factor  				// Distance FS / PointPot
    Var 0111, name Lever2_factor  				// Apply Distance_Pot to Distance FS  
    Var 0112, name Pot1_factor  					// Distance Pot / PointPot
    Var 0113, name Pot2_factor  					// Apply Distance_Pot to Distance Lever 
    
    Var 0038, name Flusi, Link FSUIPC_IN, Offset $3308, Length 2	// what Flusi-version is in use?
    {
      &dead_area1 = 5     			// to avoid jitter, we define a 'dead area' for the potentiometers
      &break_dist1 = 20      		// how many points we need for break the motors to zero
      &current_break1 = 50   		// we can define a break current for the motor
      &current_run1 = 70     		// Speed for motor when running
      &dead_area2 = 5        
      &break_dist2 = 20     
      &current_break2 = 50     
      &current_run2 = 70
    }
    
    Var 0005, name Leverdiscon, Link FSUIPC_OUT, Offset $310A, Length 1	// Disconnect both LeverPotentiometers from FS
    Var 0045, name Lever1_from_FS, Link FSUIPC_OUT, Offset $3330, Length 2
    Var 0046, name Lever2_from_FS, Link FSUIPC_OUT, Offset $3332, Length 2
    Var 0060, name CL_PSS 
    Var 0061, name FLX_PSS
    Var 0062, name TOGA_PSS
    
    
    
    // read the first four letters of the name of the airplane form AIR-file
    // to see if it is a standard- or non-standard plane
    Var 0140, name AIRFILE1, Link FSUIPC_IN, Offset $3c09, Length 1          // 1st letter of Airplane name in FS9
    Var 0141, name AIRFILE2, Link FSUIPC_IN, Offset $3c0a, Length 1          // 2nd letter of Airplane name
    Var 0142, name AIRFILE3, Link FSUIPC_IN, Offset $3c0b, Length 1          // 3rd letter of Airplane name
    Var 0143, name AIRFILE4, Link FSUIPC_IN, Offset $3c0c, Length 1          // 4th letter of Airplane name
    Var 0144, name AIRFILE5, Link FSUIPC_IN, Offset $3c0d, Length 1          // 5th letter of Airplane name
    Var 0145, name AIRFILE6, Link FSUIPC_IN, Offset $3d00, Length 1          // 1st letter of Airplane name in FSX
    Var 0146, name AIRFILE7, Link FSUIPC_IN, Offset $3d01, Length 1          // 2nd letter of Airplane name
    Var 0147, name AIRFILE8, Link FSUIPC_IN, Offset $3d02, Length 1          // 3rd letter of Airplane name
    Var 0148, name AIRFILE9, Link FSUIPC_IN, Offset $3d03, Length 1          // 4th letter of Airplane name
    Var 0149, name AIRFILE10, Link FSUIPC_IN, Offset $3d04, Length 1          // 5th letter of Airplane name
    Var 0150, name AIRFILE11, Link FSUIPC_IN, Offset $3d05, Length 1          // 6th letter of Airplane name
    Var 0151, name AIRFILE12, Link FSUIPC_IN, Offset $3d06, Length 1          // 7th letter of Airplane name
    Var 0152, name AIRFILE13, Link FSUIPC_IN, Offset $3d07, Length 1          // 8th letter of Airplane name
    Var 0153, name AIRFILE14, Link FSUIPC_IN, Offset $3d08, Length 1          // 8th letter of Airplane name
    Var 0154, name AIRFILE15, Link FSUIPC_IN, Offset $3d09, Length 1          // 10th letter of Airplane name
    Var 0155, name AIRFILE16, Link FSUIPC_IN, Offset $3d0a, Length 1          // 11thletter of Airplane name
    Var 0156, name AIRFILE17, Link FSUIPC_IN, Offset $3d0b, Length 1          // 12letter of Airplane name
    Var 0157, name AIRFILE18, Link FSUIPC_IN, Offset $3d0c, Length 1          // 13thletter of Airplane name
    Var 0158, name AIRFILE19, Link FSUIPC_IN, Offset $3d0d, Length 1          // 14th letter of Airplane name
    Var 0159, name AIRFILE20, Link FSUIPC_IN, Offset $3d0e, Length 1          // 15thletter of Airplane name
    Var 0160, name AIRFILE21, Link FSUIPC_IN, Offset $3d0f, Length 1          // 16th letter of Airplane name
    
    // Variables for LevelD
    Var 0081, name IAS_Lvld
    Var 0082, name VS_Lvld
    Var 0083, name ALT_Lvld 
    Var 0084, name APP_Lvld 
    Var 0085, name N1_Lvld
    Var 0086, name SPD_Lvld
    Var 0087, name VNAV_Lvld
    
    // Variables for PM
    Var 0070, name IAS_PM
    Var 0071, name VS_PM
    Var 0072, name ALT_PM 
    Var 0073, name APP_PM 
    Var 0074, name N1_PM
    Var 0075, name SPD_PM
    Var 0076, name AT_PM
    Var 0077, name AP_L_PM
    Var 0078, name AP_C_PM
    Var 0079, name AP_R_PM
    
    Var 0114, name LOC_PM
    Var 0115, name LNAV_PM
    Var 0116, name VNAV_PM
    Var 0117, name HDG_PM
    Var 0118, name FLCH_PM
    Var 0119, name MACH_PM
    
    
    
    // Standard- or Non-Standard Planes?
    Var 0057, name PMDG									 // PMDG
    Var 0056, name LVLD									 // LevelD
    Var 0058, name PSS									 // PSS Airbus
    Var 0059, name PF	 									 // Project Fokker
    Var 0054, name Std									 // Standard Plane
    Var 0055, name PM 									 // Project Magenta
    Var 0063, name FeelThere 								 // FeelThere Airbus
    Var 0064, name APL_Lvld 								 // Autopilot L LevelD
    Var 0065, name APC_Lvld  								 // Autopilot C LevelD
    Var 0066, name APR_Lvld  								 // Autopilot R LevelD
    Var 0067, name FLCH_Lvld  								 // FlightLevelChange LevelD
    
    // LevelD: read MPC status from FSCONV 5.5. 
    // Thanks to Nico Kaan for his great work!
    // www.nicokaan.nl
    
    Var 0092, name LvlD_Flg, Link FSUIPC_IN, Offset $8BAC, Length 4  		 
    {
     &APL_Lvld = TESTBIT &LvlD_Flg, 2
     &APC_Lvld = TESTBIT &LvlD_Flg, 3 
     &APR_Lvld = TESTBIT &LvlD_Flg, 4
     &VNAV_Lvld = TESTBIT &LvlD_Flg, 9
     &FLCH_Lvld = TESTBIT &LvlD_Flg, 10
     &VS_Lvld = TESTBIT &LvlD_Flg, 12
     &ALT_Lvld = TESTBIT &LvlD_Flg, 13
     &APP_Lvld = TESTBIT &LvlD_Flg, 15
     &N1_Lvld = TESTBIT &LvlD_Flg, 17
     &SPD_Lvld = TESTBIT &LvlD_Flg, 18
    }
    
    Var 0095, name PMDG_Flg, Link FSUIPC_IN, Offset $62BC, Length 4  		 
    {
     // &VS_PMDG = TESTBIT &PMDG_Flg, 24
     // &ALT_PMDG = TESTBIT &PMDG_Flg, 23
    &APP_PMDG = TESTBIT &PMDG_Flg, 21
     // &N1_PMDG = TESTBIT &PMDG_Flg, 15
     // &SPD_PMDG = TESTBIT &PMDG_Flg, 16
     // &CMD_A_PMDG = TESTBIT &PMDG_Flg, 8
    &CMD_B_PMDG = TESTBIT &PMDG_Flg, 9
     // &CWS_A_PMDG = TESTBIT &PMDG_Flg, 25
     // &CWS_B_PMDG = TESTBIT &PMDG_Flg, 26
    
    }
    
    
    // *** For ProjectMagenta Users:
    
    Var 0080, name PM_Flg, Link FSUIPC_IN, Offset $04F0, Length 2  		 
    {
     &IAS_PM = TESTBIT &PM_Flg, 9			
     &VS_PM = TESTBIT &PM_Flg, 2
     &ALT_PM = TESTBIT &PM_Flg, 3
     &APP_PM = TESTBIT &PM_Flg, 4
     &N1_PM = TESTBIT &PM_Flg, 10
     &SPD_PM = TESTBIT &PM_Flg, 9
     &AT_PM = TESTBIT &PM_Flg, 11
     &AP_L_PM = TESTBIT &PM_Flg, 0
     &AP_C_PM = TESTBIT &PM_Flg, 1
     &AP_R_PM = TESTBIT &PM_Flg, 13
     &LOC_PM = TESTBIT &PM_Flg, 5
     &LNAV_PM = TESTBIT &PM_Flg, 6
     &VNAV_PM = TESTBIT &PM_Flg, 14
     &HDG_PM = TESTBIT &PM_Flg, 7
     &FLCH_PM = TESTBIT &PM_Flg, 8
     &MACH_PM = TESTBIT &PM_Flg, 15
    
    }
    
    // Variables for PMDG
    // Thanks for the Offset List to shadow.sp@gmx.net, http://members.chello.at/spatat/pmdg.htm
    
    Var 0091, name IAS_PMDG, Link FSUIPC_IN, Offset $621E, Length 2          	// PMDG:is IAS_HOLD active? 0=arm,1=speed,2=n1
    Var 0088, name ALT_PMDG, Link FSUIPC_IN, Offset $622A, Length 2       		// PMDG: is ALT hold active? Values from 1 to 9
    Var 0089, name AP_PMDG, Link FSUIPC_IN, Offset $6226, Length 2	 		// PMDG: is AP active 0=off,256=cws,512=cmd
    Var 0090, name VS_PMDG, Link FSUIPC_IN, Offset $6230, Length 2	 	 	// PMDG: is V/S active?
     
    Var 0093, name APP_PMDG
    
    Var 0094, name CMD_B_PMDG
    // Var 0097, name N1_PMDG
    Var 0098, name SPD_PMDG
    
    
    Var 0047, name IAS                           		      		 // is IAS_HOLD active?
    Var 0049, name ALT_hold									 // ist ALT_HOLD active?
    Var 0050, name APP									 // Autopilot APP-mode
    Var 0051, name N1									 	 // Autopilot N1-mode
    Var 0052, name SPD									 // Autopilot Speed-hold-mode
    Var 0053, name VS										 // Autopilot V/S-mode
    
    // Variables for Standard Planes
    Var 0019, name Pause, Link FSUIPC_IN, Offset $0262, Length 2		 // is Pause mode active?
    Var 0021, name ALT_STD, Link FSUIPC_IN, Offset $07D0, Length 4        	 // Standard planes: AutoPilot ALT hold active?
    Var 0022, name IAS_STD, Link FSUIPC_IN, Offset $07DC, Length 4           // Standard planes: is IAS_HOLD active?
    Var 0029, name APP_STD, Link FSUIPC_IN, Offset $07FC, Length 4           // is Glideslope hold active?(GS and APP exchanged!!)
    Var 0030, name TOGA, Link FSUIPC_IN, Offset $080C, Length 4              // is TO/GA switch active?
    Var 0048, name MACH, Link FSUIPC_IN, Offset $07E4, Length 4              // is MACH_HOLD active?
    Var 0039, name AP, Link FSUIPC_IN, Offset $07BC, Length 4            // is AutoPilot MasterSwitch active? Att: not in PSS & PM!!
    
    Var 0040, name GS, Link FSUIPC_IN, Offset $0800, Length 4                // is ApproachMode active? (GS and APP exchanged!!)
    
    Var 0020, name Trim_to_FS, Link FSUIPC_OUT, Offset $0BC0, Length 2       // Send value of PitchTrim to FS
    Var 0023, name Lever2_to_FS, Link FSUIPC_OUT, Offset $0932, Length 2     // Send value of Lever2 to FS
    Var 0024, name Lever1_to_FS, Link FSUIPC_OUT, Offset $089A, Length 2     // Send value of Lever1 to FS
    // Var 0023, name Lever2_to_FS, Link FSUIPC_OUT, Offset $3332, Length 2     // Send value of Lever2 to FS
    // Var 0024, name Lever1_to_FS, Link FSUIPC_OUT, Offset $3330, Length 2     // Send value of Lever1 to FS
    Var 0031, name EngineNumbers, Link FSUIPC_IN, Offset $0AEC, Length 2     // how many engines has the plane?
    Var 0032, name Lever3_to_FS, Link FSUIPC_OUT, Offset $09CA, Length 2     // Send value of Lever3 to FS
    Var 0033, name Lever4_to_FS, Link FSUIPC_OUT, Offset $0A62, Length 2     // Send value of Lever4 to FS
    Var 0097, name LEVER_START								 // Motor for levers should start
    Var 0096, name ELEV_START								 // Motor for elevator trim should start
     
    
    Var 0068, name lever2_diff     // difference where the Lever2 is and where it should be
    Var 0069, name lever1_diff     // difference where the Lever1 is and where it should be
    Var 0027, name corr_Trim_pos   // Where ElevTrim should be (corrected to potentiometer values)
    Var 0028, name trim_diff       // difference where the Trim is and where it should be
    
     
    
    Var 0013, Link FSUIPC_IN, name L1_target, Offset $088c, Length 2     // FSX: Where Lever1 should be
    // Var 0123, Link FSUIPC_IN, name L1_target_9, Offset $089a, Length 2     // FS9: Where Lever1 should be
    // Var 0013, Link FSUIPC_IN, name L1_target, Offset $3330, Length 2     // Where Lever1 should be
    
    {
    
    // becouse the potentiometer differ in value, we align the potentiometer value to the leverlength
      L0 = &Lever1_upper - &Lever1_idle      // Upper Potentiomer Value - Idle Potentiomer Value
      L1 = 12800 / L0                        // Distance Pot = 128 * 100 becouse in SIOC are no decimal values possible
      
      &Pot1_factor = L1
    
      L0 = &Lever1_Pot - &Lever1_idle        // Corrected value from Pot to FS
      L1 = L0 * &Pot1_factor                 // apply length lever to pot
      L1 = L1 / 100                          // same as above, becouse of no decimal value possible
      L2 = &L1_target / 128
      &Lever1_diff = L1 - L2                 // where the lever is and where it should be
       
    IF &LEVER_START = 1                      // A/T is on
      {
    
      IF &Flusi = 8
       {
        &Leverdiscon = 192				// Disconnect both LeverPotentiometers from FS
       }
    
       CALL &MOTOR_LEVER                      // subroutine for motor motion
    
      }
    }
    
    Var 0012, Link FSUIPC_IN, name L2_target, Offset $0924, Length 2     // FSX: Where Lever2 should be
    // Var 0122, Link FSUIPC_IN, name L2_target_9, Offset $0932, Length 2     // FS9: Where Lever2 should be
    // Var 0012, Link FSUIPC_IN, name L2_target, Offset $3332, Length 2     // Where Lever2 should be
    {
      L0 = &Lever2_upper - &Lever2_idle      // Upper Potentiomer Value - Idle Potentiomer Value
      L1 = 12800 / L0                        // Distance Pot = 128
      
      &Pot2_factor = L1
    
      L0 = &Lever2_Pot - &Lever2_idle        // Corrected value from Pot to FS
      L1 = L0 * &Pot2_factor
      L1 = L1 / 100
      
      L2 = &L2_target / 128
        
      &Lever2_diff = L1 - L2
     
    IF &LEVER_START = 1                      // A/T is on
      {
        IF &Flusi = 8
         {
          &Leverdiscon = 192
         }
    
      CALL &MOTOR_LEVER                      // subroutine for motor2 motion
      }
    }
    
    Var 0018, Link FSUIPC_IN, name Trim_target, Offset $0BC2, Length 2     // Where Elevator Trim should be
    {
      IF &Trim_target > 33000
      {
        L0 = 81918 - &Trim_target     		// Trim down  (49153 .. 65535)
        L1 = L0 / 128     				// 65535 + 16383 = 81918
        L1 = TRUNC L1
      }
      ELSE
      {
        L0 = 16383 - &Trim_target     		// Trim up  (0 .. 16383)
        L1 = L0 / 128
        L1 = TRUNC L1
      }
      &corr_Trim_pos = L1    
      &trim_diff = &corr_Trim_pos - &Trim_Pot
    
    
    }
    
    
    Var 0006, name Lever1_Pot, Link USB_ANALOGIC, Input 1, PosL 0, PosC 127, PosR 254     // Lever1 Pot position 
    {
      L0 = &Lever1_upper - &Lever1_idle 	// Upper Potentiomer Value - Idle Potentiomer Value
      L1 = 16383 / L0   				// Distance FS = 16383
      L1 = TRUNC L1
      &Lever1_factor = L1
    
      L0 = &Lever1_Pot - &Lever1_idle    	// Corrected value from Pot to FS
      L1 = L0 * &Lever1_factor
      L1 = TRUNC L1
      IF &LEVER_START = 0     			// A/T is OFF
        {
          &lever1_motor = 0     			// motor stops
          &Leverdiscon = 0				// Connect both LeverPotentiometers to FS
          IF &EngineNumbers <= 2			// here we look how many engines the plane has
           {
            &Lever1_to_FS = L1         		// Send Lever1 Position to FS
           }
          IF &EngineNumbers = 4
           {
            &Lever1_to_FS = L1         		// Send Lever1 Position to FS
            &Lever2_to_FS = L1         		// Send Lever2 Position to FS
           }
        }  
    }
    
    Var 0007, name Lever2_Pot, Link USB_ANALOGIC, Input 2, PosL 0, PosC 127, PosR 254     // Lever2 Pot position 
    {
      L0 = &Lever2_upper - &Lever2_idle // Upper Potentiomer Value - Idle Potentiomer Value
      L1 = 16383 / L0   // Distance FS = 16383
      L1 = TRUNC L1
      &Lever2_factor = L1
    
      L0 = &Lever2_Pot - &Lever2_idle     	// Corrected value from Pot to FS
      L1 = L0 * &Lever2_factor
      L1 = TRUNC L1
      IF &LEVER_START = 0     			// A/T is OFF
        {
         &lever2_motor = 0    			// motor stops
         &Leverdiscon = 0  				// Connect both LeverPotentiometers to FS      
         IF &EngineNumbers <= 2 			// here we look how many engines the plane has
          {
           &Lever2_to_FS = L1         		// Send Lever2 Position to FS
          }
         IF &EngineNumbers = 4
          {
           &Lever3_to_FS = L1         		// Send Lever3 Position to FS
           &Lever4_to_FS = L1         		// Send Lever4 Position to FS
          }
       }
    }
    
    Var 0008, name Trim_Pot, Link USB_ANALOGIC, Input 3, PosL 0, PosC 128, PosR 254     // Trim Potentiometer position
    {
     L0 = &Trim_Pot * 128
     L1 = 16383 - L0
    
     IF &ELEV_START = 0		// Trimwheel steered by hand                      
      {
       &Trim_to_FS = L1    		// send Trimwheel to FS
       &elevator_motor = 0   	// Elevator motor stops        
      }
    }
    
    Var 0120, name Lever_Elevator, Link SUBRUTINE // Subroutine for Lever and Trim Motor movement
    
    {
    // Dedection if Standard- or Non-Standard-Plane
    
    &PM = 0
    IF &PM_Flg >= 1
      {
       &PM = 1			// PM started
      }
    
    IF &PM = 0
    {
      &PMDG = 0
      IF &AIRFILE1 = 80
       {
        IF &AIRFILE2 = 77
        {
         IF &AIRFILE3 = 68
          {
           IF &AIRFILE4 = 71						
           {
             &PMDG = 1							// Plane is PMDG
           }
          }
         }
       }
    
     &lvld = 0
        IF &Flusi = 7							// FS2004
         {	
         IF &AIRFILE1 = 76						// l
          {
          IF &AIRFILE2 = 86						// v
           {
            IF &AIRFILE3 = 76					// l
            {
             IF &AIRFILE4 = 68					// d						
              {
               &lvld = 1				      	// Plane is LevelD767
              }						
            }
           }
          }
         }
       
        IF &Flusi = 8						     // FSX
         {
         IF &AIRFILE7 = 101						// E
          {
          IF &AIRFILE8 = 118					// V
           {
            IF &AIRFILE9 = 101					// E
            {
             IF &AIRFILE10 = 108					// L						
             {
               &lvld = 1					// Plane is LevelD767
             }
            }
           }
          }
         }
    
    
    
      &PSS = 0
      IF &AIRFILE1 = 80						// P
       {
        IF &AIRFILE2 = 115						// S
        {
         IF &AIRFILE3 = 115						// S
         {
          IF &AIRFILE4 = 65						// A						
          {
           &PSS = 1							// Plane is PSS Airbus (PSSA)
          }
         }
        }
       }
    
      &FeelThere = 0
        IF &Flusi = 7						  	// FS2004
         {
         IF &AIRFILE13 = 114					// r
          {
          IF &AIRFILE14 = 101					// e
           {
            IF &AIRFILE15 = 32
            {
             IF &AIRFILE16 = 65					// A						
              {
               &FeelThere = 1				      // Plane is FeelThere Airbus
              }						
            }
           }
          }
         }
       
        IF &Flusi = 8						  	// FSX
         {
         IF &AIRFILE13 = 114					// r
          {
          IF &AIRFILE14 = 101					// e
           {
            IF &AIRFILE15 = 32
            {
             IF &AIRFILE16 = 65					// A						
             {
               &FeelThere = 1					// Plane is FeelThere Airbus
             }
            }
           }
          }
         }
    
    
      IF &PMDG = 1 							// PMDG Airplane  
       {
    
    // &IAS = &IAS_PMDG
    // &N1  = &N1_PMDG
    // &ALT_hold = &ALT_STD						// AP of PMDG often switches off ALT_HOLD so we use STD instead
    
        IF &IAS_PMDG >= 1
         {
         &IAS = 1
         }
         ELSE
         {
         &IAS = 0
         }   		 
     				 
        &APP = &APP_PMDG						// ist APP_PMDG APP 
        &VS = &VS_PMDG
       
        IF &ALT_PMDG >= 1
         {
         &ALT_hold = 1
         }
         ELSE
         {
         &ALT_hold = 0
         }   		 
       }
    
      IF &LVLD = 1 							// LevelD Airplane  
       {
        &IAS = &IAS_Lvld 				 
        &ALT_hold = &ALT_Lvld
        &APP = &APP_Lvld
        &N1 = &N1_Lvld
        &SPD = &SPD_Lvld
        &VS = &VS_Lvld
        &IAS = &VNAV_Lvld
       }
    
      IF &PSS = 1 							// PSS Aibus
       {
        &IAS = &IAS_STD 						// In this time all are Standard			 
        &ALT_hold = &ALT_STD					// but shortly we will find adresses for PSS
        &APP = &GS							// PSS uses GS instead of APP (or vice versa?)		 
       }
    
      IF &Std = 1           					 // Standard Airplane
        {
         &IAS = &IAS_STD  				 
         &ALT_hold = &ALT_STD
         &APP = &APP_STD 			 
        }
    }
    
    IF &PM = 1           					 	// Project Magenta
      {
       &IAS = &IAS_PM 									 
       &N1 = &N1_PM
       &SPD = &SPD_PM
       &ALT_hold = &ALT_STD		// MCP often switches here to 0 but it should remain 1 !! So we use STD and not PM
       &APP = &APP_PM
       &VS = &VS_PM
      }
    
    &Std = 0
    IF &PMDG = 0
     { 
     IF &LVLD = 0
      {
      IF &PSS = 0
       {
       IF &PF = 0
        {
        IF &PM = 0
           {
            &Std = 1			// FeelThere in the moment is standard plane
           }
        }
       }
      }
     }
     									 
        
    
    
    // Start Relais for FeelThere
    
    IF &FeelThere = 1
     {
      &Relais = 120
     }
    ELSE
     {
      &Relais = 0
     }
    
    
    
    // now we look if the levermotors should  start or stop
      
        &LEVER_START = 0
        IF &Pause = 0 
         {
          IF &PSS = 0			// Airbus has no Motorized Throttles  !!
           {
            IF &FeelThere = 0
             {    
              &LEVER_START = 1
             }
           }
         }
      
     
    IF &IAS = 0
       {
        IF &MACH = 0
         {
          IF &TOGA = 0
    	 {
    	  IF &FLCH_Lvld = 0	// When FLCH is set, LevelD switches SPD to 0, so Throttles would stop
             {
              IF &N1 = 0
               {
                IF &SPD = 0
                 {
       	        &LEVER_START = 0
                 }
    	     }
             } 
           }
         }
       }      
    
    // now we look if the elevator motor should  start or stop
    
      IF &Pause = 0 
        {
         IF &AP = 1
          {
           &ELEV_START = 1
          }
         ELSE
          {
           &ELEV_START = 0
          }
     
        }
      ELSE
        {
         &ELEV_START = 0
        }
    
    
       
       
    
        IF &ALT_hold = 0				// ALT hold is on
         {
         IF &APP = 0					// APP hold is on
          {
           IF &VS = 0					// V/S mode is on
            {
             IF &AP_L_PM = 0       		// all AP of PM are off
              {
               IF &AP_C_PM = 0       		
                {
                 IF &AP_R_PM = 0       		
                  {
       	         IF &AP_PMDG = 0 		// Autopilot PMDG is off      		  
                    {
    		      IF &APL_LvlD = 0       // Autopilot LevlD is off       		
                        {
                         IF &APC_LvlD = 0       		
                          {
                           IF &APR_LvlD = 0       		  
    //                        {
    //				 IF &AP = 0		// Autopilot Standard is off
    				  {
                              &ELEV_START = 0		// Elevator Motor stop
    			        }
    //			      }
    			    }
                        }
    			}
    		    
                  }
                } 
              }
            }
          }
        }      
         
    
      IF &ELEV_START = 1                       // Elevator Motor should start
      {
       CALL &Motor_Elevator				// subroutine for motor motion
      }
    }
    
    
    
    Var 0125, name Motor_Lever, Link SUBRUTINE     // USB_DC controls motors for Lever1&2
    
    // Motor control  0-127 = left; 129-255 =Right; 0 stops 
    {
      L0 = &lever1_diff    
      L1 = 0    
      IF L0 < 0
       {
        L1 = 128 				// Motor run direction   
       }
      L0 = ABS L0
      L2 = &current_run1 + L1		// Lever1 Motor runs with full current
      IF L0 <= &break_dist1
       {
        L2 = &current_break1 + L1		// Lever1 Motor runs with break current
       }
      L0 = ABS L0
      IF L0 <= &dead_area1
       {
        L2 = 0    
       }
      IF &LEVER_START = 0
       {
        L2 = 0  		   		// Lever1 Motor stops
       }
    
    &lever1_motor = L2 
      
      L0 = &lever2_diff    
      L1 = 128    
      IF L0 < 0
       {
        L1 = 0    
       }
      L0 = ABS L0
      L2 = &current_run2 + L1		// Lever2 Motor runs with full current
      IF L0 <= &break_dist2
       {
        L2 = &current_break2 + L1       // Lever2 Motor runs with break current
       }
      L0 = ABS L0
      IF L0 <= &dead_area2
       {
        L2 = 0    
       }
      IF &LEVER_START = 0 
       {
        L2 = 0    				// Lever2 Motor stops                       
       }
      
    &lever2_motor = L2    
    }
    
    
    Var 0130, name Motor_Elevator, Link SUBRUTINE     // USB_DC controls motor for Elevator
    // Motor control  0-127=left, 128 stops, 129-255=right
    {
      L0 = &trim_diff    
      IF &Flusi = 7						  // FS2004
       {
        IF L0 < 0
         {
          L1 = 128
         } 
         ELSE
         {
          L1 = 0
         }
       }
      IF &Flusi = 8						  // FSX
       {
        IF L0 > 0
         {
          L1 = 0
         }   
        ELSE
         {
          L1 = 128
         } 
       }
     
     
      L0 = ABS L0
      L2 = &current_break3 + L1
      IF L0 <= &break_dist3
      {
        L2 = &current_run3 + L1
      }
      L0 = ABS L0
      IF L0 <= &dead_area3
      {
        L2 = 0    
      }
       
    
      IF &ELEV_START = 0     // Motor Elevator trim stop
          {
            L2 = 0 
          }   
      &elevator_motor = L2    
    }

  3. #3
    75+ Posting Member
    Join Date
    Dec 2006
    Location
    Israel
    Posts
    126
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Re: SIOC Code for Elevator Trim, OC USBDCMotors, Project Magenta

    I used the bit older version of this script with usb OC dcmotors card and Magenta , and can confirm --works

    Regards and tnx for updated script--no way to get this one those days

    Joseph

  4. #4
    New Member
    Join Date
    Jan 2012
    Location
    SPAIN
    Posts
    3
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Re: SIOC Code for Elevator Trim, OC USBDCMotors, Project Magenta

    Quote Originally Posted by yoss View Post
    I used the bit older version of this script with usb OC dcmotors card and Magenta , and can confirm --works

    Regards and tnx for updated script--no way to get this one those days

    Joseph

    Hello Joseph.
    I use Airbus, Project Magenta, OpenCockpits dcmotorplus and FSX.
    I little question: Do you have to erase or change something in this script (related with FS9, PSS, PMDG...)?
    Thanks and best regards.
    Emilio

  5. #5
    New Member
    Join Date
    Jan 2012
    Location
    SPAIN
    Posts
    3
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Re: SIOC Code for Elevator Trim, OC USBDCMotors, Project Magenta

    Hello Joseph.
    I use Airbus, Project Magenta, OpenCockpits dcmotorplus and FSX.
    I little question: Do you have to erase or change something in this script (related with FS9, PSS, PMDG...)?
    Thanks and best regards.
    Emilio

Similar Threads

  1. B73x Elevator Trim
    By shearder in forum Cockpit Parts and Motion Platforms
    Replies: 0
    Last Post: 12-06-2009, 04:08 PM
  2. SIOC Elevator Pot Code
    By tomenglish2000 in forum OpenCockpits General Discussion
    Replies: 0
    Last Post: 09-28-2009, 06:26 AM
  3. Elevator trim
    By hercules in forum PM General Q & A
    Replies: 0
    Last Post: 01-26-2009, 01:00 PM
  4. Working Sioc code for elevator/ Ailerons
    By hercules in forum OpenCockpits General Discussion
    Replies: 0
    Last Post: 01-25-2009, 08:28 PM
  5. Replies: 3
    Last Post: 08-15-2008, 03:29 AM