Results 11 to 20 of 27
Thread: help ref wiring
-
11-02-2010, 05:54 PM #11
-
11-02-2010, 06:03 PM #12
Re: help ref wiring
Go to step 5 and see if there's any voltage. Do you have a multimeter?
-
11-02-2010, 06:27 PM #13
Re: help ref wiring
Steve
For reasons I'm not sure off, it appears your PSU doesn't comply with the ATX wiring colour scheme. In that instance the green wire is used to turned the power supply on. I notice in your pictures, Grey is indicated as PS_ON. Grey is normally Power OK. If you get nothing at step 5, go back to step 4 and change green to grey.
Sean
-
11-03-2010, 04:14 AM #14
Re: help ref wiring
No readings off meter, so grey to ANY black wire then.
Will report back
EDIT.
Ok so connected the grey to a black from same block and we have power.
I still cant get no readings from multimeter but being new i may have it on wrong settings.
http://www.maplin.co.uk/Module.aspx?...37279&T=Module
Thats my multimeter,
I have the black in bottom socket.
I have the red in the socket above that.
The dial turned to the left to 20 (10 oclock position)
steveLast edited by BishBash; 11-03-2010 at 05:03 AM. Reason: Wiring done
-
11-03-2010, 06:38 AM #15
Re: help ref wiring
I can't open that link on my phone Steve. The black lead is normally marked common or com. The red lead goes into the one marked V. Make sure the dial is set to Volts dc not ac.
-
11-03-2010, 07:33 AM #16
-
11-03-2010, 12:54 PM #17
Re: help ref wiring
hello steve......
if you're not in a panic and can wait until after the FSWeekend show, i have a PSU unit here
which works fine (got a green wire) which you are welcome to have.
i can pop you a switch on the green black wire combination and label up the 5v and 12v leads
for you. just trying to help out here
rgds ...
ianMr. Ian. P. Sissons is hereby recognised as an Honorary Flight Sim Captain following his passing in February 2016. This is in recognition for his commitment to Flight Simulation.
www.mycockpit.org Featured Builder August 2008 www.737ng.co.uk
FS9/PROSIM737/CPFLIGHT/Lots of BU0836X's and a Beer Fridge
-
11-03-2010, 04:21 PM #18
-
11-03-2010, 04:47 PM #19
Re: help ref wiring
Sean,
No meter readings off my mulimeter,any ideas
steve
-
11-03-2010, 04:59 PM #20
Re: help ref wiring
Are you making contact with the probes? Do they fit into the connectors?
Similar Threads
-
Wiring the o/c boards
By Drewsta in forum OpenCockpits General DiscussionReplies: 6Last Post: 12-17-2009, 01:48 AM -
Need a wee bit of help wiring....
By Crescent in forum Computer Hardware SetupReplies: 2Last Post: 03-13-2009, 01:37 AM -
wiring
By phil. in forum OpenCockpits General DiscussionReplies: 3Last Post: 09-15-2008, 03:38 AM -
Easier wiring
By Lezam in forum I/O Interfacing Hardware and SoftwareReplies: 5Last Post: 02-22-2008, 12:20 AM -
Wiring
By imported_767300 in forum General Builder Questions All Aircraft TypesReplies: 10Last Post: 06-10-2007, 01:46 PM
Looking for fun companions for travels and adventures? Authentic Ladies Premier Сasual Dating
Top-notch Сasual Dating -...