Results 1 to 6 of 6

Thread: Doing Duz

  1. #1
    150+ Forum Groupie flatlandpilot's Avatar
    Join Date
    May 2009
    Location
    Netherlands, Zwolle
    Posts
    152
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Doing Duz

    grey pvc, thats grey already and doesn't crack.




    When once you have tasted flight,
    you will forever walk the earth with your eyes turned skyward

  2. #2
    150+ Forum Groupie flatlandpilot's Avatar
    Join Date
    May 2009
    Location
    Netherlands, Zwolle
    Posts
    152
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Re: Doing Duz

    sprayed with airbus grey-blue


    sizes:
    outside diameter: 10 mm.
    inside diameter 7.1 mm. / 3.1 mm. deep.
    hole: 4 mm. total height: 6 mm

    The top of the duz is 3mm. raised above the panel
    The screw top is 1mm. below the duz top.
    When once you have tasted flight,
    you will forever walk the earth with your eyes turned skyward

  3. Thanks Westozy thanked for this post
  4. #3
    MyCockpit Support Staff


    Westozy's Avatar
    Join Date
    Nov 2005
    Location
    Perth, Western Australia
    Posts
    1,488
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Re: Doing Duz

    Sweet,

    Cheers, Gwyn

    737NG using Prosim737, Immersive Calibration Pro, Aerosim Solutions motorized TQ & cockpit hardware, CP Flight MCP & FDS SYS1X, SYS2X & SYS4X, FDS PRO FMCs, AFDS units & Glarewings, Matrix Orbital ELEC display, Pokeys Landing & Cruise alt display, Buttkicker Gamers, 3 x BenqMW811ST projectors with a Matrox Th2Go
    http://www.aerosimsolutions.com.au
    Supporter of MyCockpit.org, please join me in donating!!!

  5. #4
    150+ Forum Groupie riche543's Avatar
    Join Date
    May 2008
    Location
    Sydney Australia
    Posts
    264
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Re: Doing Duz

    They look great Flatland, Did you have to change the bit for the rounded/beveled top ?. Would you like to share the dxf or gcode for um..
    Cheers
    Rich..

  6. #5
    150+ Forum Groupie flatlandpilot's Avatar
    Join Date
    May 2009
    Location
    Netherlands, Zwolle
    Posts
    152
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Re: Doing Duz

    the dxf file are 3 centred circles with a diameter of 4, 7.1 and 10 mm.
    yes I had to change the bit, but thats no problem.

    for rounding I use this one

    http://www.homedepot.ca/webapp/wcs/s...k=P_PartNumber
    (and modified it by cutting off the "guide" / lower part)
    When once you have tasted flight,
    you will forever walk the earth with your eyes turned skyward

  7. #6
    150+ Forum Groupie flatlandpilot's Avatar
    Join Date
    May 2009
    Location
    Netherlands, Zwolle
    Posts
    152
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Re: Doing Duz

    When once you have tasted flight,
    you will forever walk the earth with your eyes turned skyward