Results 1 to 2 of 2
  1. 03-14-2010, 11:19 PM #1
    Buddym
    Buddym is offline
    300+ Forum Addict
    Tutorial Contributor / Point Value: 10
    Total Awards: 1
    Total Points: 10



    Join Date
    Jan 2009
    Location
    Tampa
    Posts
    487
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Question for Gwyn

    Hi Gwyn,

    I wanted to ask you about the bevel on your panels... I appears that on many of your panels there are beveled edges on the cutouts for switches and displays. It looks very nice. Do you do this with a special bit? I think that I have seen reference to a chamfer bit..?

    thanks,
    Buddy
    Reply With Quote Reply With Quote
  2. 03-15-2010, 02:50 AM #2
    Westozy
    Westozy is offline
    MyCockpit Support Staff
    Builder Of The Month / Point Value: 100
    Total Awards: 1
    Total Points: 100



    Westozy's Avatar
    Join Date
    Nov 2005
    Location
    Perth, Western Australia
    Posts
    1,415
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Re: Question for Gwyn

    Quote Originally Posted by Buddym View Post
    Hi Gwyn,

    I wanted to ask you about the bevel on your panels... I appears that on many of your panels there are beveled edges on the cutouts for switches and displays. It looks very nice. Do you do this with a special bit? I think that I have seen reference to a chamfer bit..?

    thanks,
    Buddy
    Hi Buddy,

    Just use a 90 degree 'V' router bit to produce 45 degree bevels. I bought a cheap 1/4" router bit set from Bunnings for about $45.00, there are a couple of V bits in those sets. For the inside of my main instrument panel monitor bezels, I created a toolpath over the original drawing for three sides of the monitor bezel - (top and sides). Command the tool to follow "on the line" and set the depth of cut to what you require, I think I used a cut of 3mm deep to place the bevel half the thickness of the bezel piece.

    Gwyn...
    Last edited by Westozy; 03-15-2010 at 02:52 AM.

    737NG using Prosim737, Immersive Calibration Pro, Aerosim Solutions motorized TQ & cockpit hardware, CP Flight MCP & FDS SYS1X, SYS2X & SYS4X, FDS PRO FMCs, AFDS units & Glarewings, Matrix Orbital ELEC display, Pokeys Landing & Cruise alt display, Buttkicker Gamers, 3 x BenqMW811ST projectors with a Matrox Th2Go
    http://www.aerosimsolutions.com.au
    Supporter of MyCockpit.org, please join me in donating!!!
    Reply With Quote Reply With Quote
« Previous Thread | Next Thread »

Similar Threads

  1. Another Question for Gwyn
    By Buddym in forum CNC Discussion
    Replies: 2
    Last Post: 03-18-2010, 02:32 PM
  2. Gwyn Tutorial
    By maliga00 in forum CNC Discussion
    Replies: 3
    Last Post: 02-25-2010, 08:06 PM
  3. Gwyn Perrett's Article "Creating a glass cockpit display"
    By Matt Olieman in forum General Builder Questions All Aircraft Types
    Replies: 0
    Last Post: 08-31-2007, 07:20 PM
  4. Happy Birthday Gwyn (Westozy)
    By Matt Olieman in forum General Builder Questions All Aircraft Types
    Replies: 13
    Last Post: 07-31-2007, 06:31 PM