Results 1 to 6 of 6
  1. #1
    Executive Vice President, MyCockpit


    Matt Olieman's Avatar
    Join Date
    Oct 2005
    Location
    Ocala, FL USA
    Posts
    3,155
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Thumbs up Wendy Thank You For The Very Interesting and Informative Interview :)



    I want to thank Wendy for a wonderful and informative interview.
    It's nice to get to know about CNC from a different perspective, I find the interview very interesting!!!!
    Makes me want to go out and buy one

    Thank you Wendy

    For those who missed the home page introduction to Wendy's interview Go Here: http://www.mycockpit.org/forums/cont...er-CNC-Machine

    Matt Olieman
    Last edited by Matt Olieman; 03-11-2010 at 08:56 AM. Reason: forgot link

  2. #2
    150+ Forum Groupie twisted8's Avatar
    Join Date
    Jun 2009
    Location
    California
    Posts
    243
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Re: Wendy Thank You For The Very Interesting and Informative Interview :)

    Very inspirational! great info!

  3. #3
    500+ This must be a daytime job ian@737ng.co.uk's Avatar
    Join Date
    Jan 2006
    Location
    Oswestry, Shropshire
    Posts
    677
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Re: Wendy Thank You For The Very Interesting and Informative Interview :)

    thanks wendy...........
    that was some very interesting and educational reading........
    excellent
    regards ... ian
    Mr. Ian. P. Sissons is hereby recognised as an Honorary Flight Sim Captain following his passing in February 2016. This is in recognition for his commitment to Flight Simulation.

    www.mycockpit.org Featured Builder August 2008 www.737ng.co.uk
    FS9/PROSIM737/CPFLIGHT/Lots of BU0836X's and a Beer Fridge

  4. #4
    150+ Forum Groupie
    Join Date
    Jul 2008
    Location
    Belgium
    Posts
    284
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Re: Wendy Thank You For The Very Interesting and Informative Interview :)

    Thank you all. It was a pleasure doing this interview. Hope to inspire a lot of people to start with CNC.


    Regards, Wendy

  5. #5
    10+ Posting Member Rob-PA7RM's Avatar
    Join Date
    Nov 2009
    Location
    Netherlands
    Posts
    18
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Re: Wendy Thank You For The Very Interesting and Informative Interview :)

    I even made a post on the dutch simFlight.NL website
    http://simflight.nl/2010/03/intervie...y-cnc-machine/

    Nice to read the interview.
    Rob.
    Flightsim news @

  6. #6
    500+ This must be a daytime job



    Join Date
    Jan 2009
    Location
    Tampa
    Posts
    531
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Re: Wendy Thank You For The Very Interesting and Informative Interview :)

    No doubt! A great tutorial! Between yourself and Westozy, the builders here will be machining parts for everything! I can't wait to get my machine fixed so I can try a couple of your techniques out!

    Buddy

Similar Threads

  1. Wendy and CNC Builders... Question on PCBs
    By Buddym in forum CNC Discussion
    Replies: 27
    Last Post: 08-20-2010, 02:12 PM
  2. Interview with Flt 1549 CoPilot
    By Tomlin in forum General Discussion
    Replies: 1
    Last Post: 04-17-2009, 07:54 PM
  3. Re: Interview
    By Bob Reed in forum PM General Q & A
    Replies: 0
    Last Post: 03-31-2006, 03:14 PM
  4. Interview
    By Bob Reed in forum PM General Q & A
    Replies: 0
    Last Post: 03-19-2006, 07:02 PM
  5. Daken Skys interview, first Q&A published
    By Kester Meijer in forum PM General Q & A
    Replies: 0
    Last Post: 03-18-2006, 12:06 PM