Results 1 to 8 of 8

Thread: Gear switch

  1. #1
    150+ Forum Groupie flatlandpilot's Avatar
    Join Date
    May 2009
    Location
    Netherlands, Zwolle
    Posts
    152
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Gear switch

    Here some pictures of my gear switch.
    build from 3mm PVC.



    When once you have tasted flight,
    you will forever walk the earth with your eyes turned skyward

  2. Thanks Buddym, Westozy, Geremy Britton thanked for this post
  3. #2
    MyCockpit Support Staff


    Westozy's Avatar
    Join Date
    Nov 2005
    Location
    Perth, Western Australia
    Posts
    1,488
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Re: Gear switch

    Here's my simple solution to the B737 gear lever...



    Cheers, Gwyn

    737NG using Prosim737, Immersive Calibration Pro, Aerosim Solutions motorized TQ & cockpit hardware, CP Flight MCP & FDS SYS1X, SYS2X & SYS4X, FDS PRO FMCs, AFDS units & Glarewings, Matrix Orbital ELEC display, Pokeys Landing & Cruise alt display, Buttkicker Gamers, 3 x BenqMW811ST projectors with a Matrox Th2Go
    http://www.aerosimsolutions.com.au
    Supporter of MyCockpit.org, please join me in donating!!!

  4. Thanks dukabr, caKus thanked for this post
  5. #3
    150+ Forum Groupie flatlandpilot's Avatar
    Join Date
    May 2009
    Location
    Netherlands, Zwolle
    Posts
    152
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Re: Gear switch

    the finished gearswitch.


    When once you have tasted flight,
    you will forever walk the earth with your eyes turned skyward

  6. #4
    500+ This must be a daytime job



    Join Date
    Jan 2009
    Location
    Tampa
    Posts
    531
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Re: Gear switch

    great lookin asssembly, nice work! Similar to mine in some respects.

    Buddy

  7. #5
    150+ Forum Groupie flatlandpilot's Avatar
    Join Date
    May 2009
    Location
    Netherlands, Zwolle
    Posts
    152
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Re: Gear switch

    build in and backlighted.
    for backlighting I used 5 mm. 100 degr amber leds being placed 18mm. behind the panel,
    10 leds, each 15 mm. one, my day is saved

    When once you have tasted flight,
    you will forever walk the earth with your eyes turned skyward

  8. #6
    500+ This must be a daytime job



    Join Date
    Jan 2009
    Location
    Tampa
    Posts
    531
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Re: Gear switch

    that looks great! what did you end up doing for gear position annunciators?

    Buddy

  9. #7
    150+ Forum Groupie flatlandpilot's Avatar
    Join Date
    May 2009
    Location
    Netherlands, Zwolle
    Posts
    152
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Re: Gear switch

    2 small microswitches.
    Buddy, as you can see on the left of the photo, I'm ready for
    gear lights (as a training for the korry's )
    When once you have tasted flight,
    you will forever walk the earth with your eyes turned skyward

  10. #8
    150+ Forum Groupie riche543's Avatar
    Join Date
    May 2008
    Location
    Sydney Australia
    Posts
    264
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Re: Gear switch

    Luvly jubly well done looks great

Similar Threads

  1. Gear LED's
    By Clive in forum I/O Interfacing and Hardware
    Replies: 5
    Last Post: 04-09-2011, 03:38 AM
  2. CNC Gear Machining
    By Westozy in forum Westozy's Mechanical Engineering
    Replies: 6
    Last Post: 12-06-2009, 04:32 AM
  3. Avionics Master Switch vs. Avionics Switch???
    By Tomlin in forum I/O Interfacing Hardware and Software
    Replies: 4
    Last Post: 08-08-2008, 10:28 AM
  4. gear up gear down
    By Radar in forum Where to Start Building a Home Cockpit
    Replies: 47
    Last Post: 04-14-2007, 02:00 AM
  5. Gear instructions
    By michelmvd in forum FS2Phidget Users
    Replies: 6
    Last Post: 03-14-2007, 10:19 AM