Page 2 of 2 FirstFirst 12
Results 11 to 16 of 16
  1. 04-07-2010, 04:08 PM #11
    No Longer Active
    No Longer Active is offline
    1000+ Poster - Fantastic Contributor
    Join Date
    Nov 2008
    Location
    Europe
    Posts
    1,934
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Re: Laser engraved back lit panel suppliers

    Hi, these guys will do it, but they will cost you a fair bit because of their setup fee's, drawing fee's etc...

    Depends how much you really want it I suppose:

    http://www.engravingworld.net/

    Not cheap, but top notch, they have done a few bits for me in the past.

    They are up the road from me too which is handy!
    GA or the Highway!
    Reply With Quote Reply With Quote
  2. 04-07-2010, 08:17 PM #12
    Westozy
    Westozy is offline
    MyCockpit Support Staff
    Builder Of The Month / Point Value: 100
    Total Awards: 1
    Total Points: 100



    Westozy's Avatar
    Join Date
    Nov 2005
    Location
    Perth, Western Australia
    Posts
    1,415
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Re: Laser engraved back lit panel suppliers

    Hi Dean,
    I can supply rotary engraved backlight panels for any type of aircraft! See http://www.aerosimsolutions.com.au/panels.html

    Regards, Gwyn

    737NG using Prosim737, Immersive Calibration Pro, Aerosim Solutions motorized TQ & cockpit hardware, CP Flight MCP & FDS SYS1X, SYS2X & SYS4X, FDS PRO FMCs, AFDS units & Glarewings, Matrix Orbital ELEC display, Pokeys Landing & Cruise alt display, Buttkicker Gamers, 3 x BenqMW811ST projectors with a Matrox Th2Go
    http://www.aerosimsolutions.com.au
    Supporter of MyCockpit.org, please join me in donating!!!
    Reply With Quote Reply With Quote
  3. 04-08-2010, 02:20 AM #13
    skalarki
    skalarki is offline
    75+ Posting Member skalarki's Avatar
    Join Date
    May 2008
    Location
    united kingdom
    Posts
    83
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Re: Laser engraved back lit panel suppliers

    Hi

    As my new service as been launched, I can do any type panels, laser cutting and high rsolutions engraving as well. Not only that, I can do all documentation FREE of charge, all the drawings etc. just need sorce for recreating them.
    Have a look on my website: http://www.a320-project. skalarki.co.uk
    Any more info - just email me please.

    Thanks

    Marcin
    Reply With Quote Reply With Quote
  4. 04-08-2010, 04:51 AM #14
    turbopropdriver
    turbopropdriver is offline
    25+ Posting Member
    Join Date
    Dec 2006
    Location
    UK
    Posts
    68
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Re: Laser engraved back lit panel suppliers

    Here's some screen shots of the manual I have. Are these sufficient to work from if I provide some basic dimensions ?








    This is a real panel and the finish that I need.

    AV-8B Sim Builder. If it won't hover, don't bovver
    Reply With Quote Reply With Quote
  5. 04-08-2010, 03:32 PM #15
    skalarki
    skalarki is offline
    75+ Posting Member skalarki's Avatar
    Join Date
    May 2008
    Location
    united kingdom
    Posts
    83
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Re: Laser engraved back lit panel suppliers

    That looks fine. I suppouse you have .pdf manual which will be even better.
    If comes to quality, thats no problem. My panels are 3 layers of quality acrylic with high resolution laser engraving.
    Reply With Quote Reply With Quote
  6. 04-09-2010, 09:21 AM #16
    turbopropdriver
    turbopropdriver is offline
    25+ Posting Member
    Join Date
    Dec 2006
    Location
    UK
    Posts
    68
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Re: Laser engraved back lit panel suppliers

    Quote Originally Posted by skalarki View Post
    That looks fine. I suppouse you have .pdf manual which will be even better.
    If comes to quality, thats no problem. My panels are 3 layers of quality acrylic with high resolution laser engraving.
    PM ed you Marcin.

    Thanks, Dean
    AV-8B Sim Builder. If it won't hover, don't bovver
    Reply With Quote Reply With Quote
Page 2 of 2 FirstFirst 12
« Previous Thread | Next Thread »

Similar Threads

  1. How can I make the back lighted letters in a plexiglass panel?
    By mirrage in forum Cockpit Parts and Motion Platforms
    Replies: 26
    Last Post: 05-22-2014, 11:11 AM
  2. My first laser cut panel
    By glider_uk in forum General Builder Questions All Aircraft Types
    Replies: 4
    Last Post: 12-16-2010, 03:05 PM
  3. Experimenting with the laser for panel engraving
    By Wendy in forum General Builder Questions All Aircraft Types
    Replies: 2
    Last Post: 11-13-2010, 07:38 AM
  4. panel suppliers in the us?
    By djcevera20 in forum General Builder Questions All Aircraft Types
    Replies: 6
    Last Post: 09-04-2009, 11:23 PM