Results 1 to 7 of 7
  1. #1
    300+ Forum Addict ak49er's Avatar
    Join Date
    Jan 2007
    Location
    Big Lake, Alaska
    Posts
    323
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Vidikron VPF 50 HD

    Gents, I just received through a donation the above projector, it is one big bad mutha'.
    This is a CRT Projector, otherwise known as an Electrohome ECP 4500.

    It is rumored to have come from the old F-15 Simulator located at Elemndorf AFB Alaska.

    Anyhow, after some trial and error I was able to get it fired up and projecting some light. The picture would not stabilize and I found the burned out component below, located on the Convergence Card, you should see how many cards and PS there is on this frame. (127lbs.)

    Support has been very hard to come by, and the only repair outfit I can find is not returning calls or emails.

    I need help in identifying the burned out component, it is labeled 476, 16k, 707, and is yellow with a orange stripe. Anyone know of it?

  2. #2
    25+ Posting Member
    Join Date
    Feb 2007
    Location
    Georgetown, Texas
    Posts
    44
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Re: Vidikron VPF 50 HD

    It is a 47 Microfarad electrolytic SMD cap.

    Dave

  3. #3
    300+ Forum Addict ak49er's Avatar
    Join Date
    Jan 2007
    Location
    Big Lake, Alaska
    Posts
    323
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Re: Vidikron VPF 50 HD

    Thanks man, I appreciate that!

    So is this something that can be simply desoldered and reinstalled, or is there more to it? And what would you think would make this device fail, anything common, over-voltage, age...?


    Got any spares? J/K

    Now I need to find a source, and hope a simple swap will set it right.

  4. #4
    25+ Posting Member
    Join Date
    Feb 2007
    Location
    Georgetown, Texas
    Posts
    44
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Re: Vidikron VPF 50 HD

    Caps failure can be caused by age, over voltage, excessive current etc. It is hard to say why your failed. Many times replacing the cap will fix the problem.

    You can get SMD caps from Mouser, DigiKey. SMD caps come in various physical sizes should be fairly cheap. I can not tell by the picture what size it is. As a test you can solder any 47 microfarad cap in its place. Be sure to observe the polarity. Th side with the line is the negative side of the cap.

    Sorry, I do not have any.

    Good luck

  5. #5
    300+ Forum Addict phil744's Avatar
    Join Date
    Aug 2007
    Location
    Lancashire, england
    Posts
    354
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Re: Vidikron VPF 50 HD

    Yup thats a 47uF 16V tantalum cap

    http://gb.mouser.com/ProductDetail/A...jJ%252bWCHI%3d
    - - - - - - - - - - - -
    Philip Lambert

    747-400? nah probably 767 now, FS9, FDT simboards , dunnow about software yet

    www.simvionics.co.uk

  6. #6
    Our new friend needs to reach 10 posts to get to the next flight level
    Join Date
    Jan 2009
    Location
    EDDH
    Posts
    8
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Re: Vidikron VPF 50 HD

    Quote Originally Posted by DaveC3 View Post
    Be sure to observe the polarity. Th side with the line is the negative side of the cap.
    This is a size C tantalum cap.

    Be aware: for tantalum SMD caps the line is the POSITIVE side.

  7. #7
    300+ Forum Addict ak49er's Avatar
    Join Date
    Jan 2007
    Location
    Big Lake, Alaska
    Posts
    323
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Re: Vidikron VPF 50 HD

    Thanks a million for all your help gentlemen!