Results 1 to 4 of 4
  1. #1
    25+ Posting Member
    Join Date
    Dec 2008
    Location
    Norway
    Posts
    38
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Smile Tutorial wanted!

    HI; Im trying to understand FSUIPC and offsets.

    How can I make some buttons on my overhead to play like a prerecorded ground handling sound (PMsound)and pushback sequence when I press the e.g ground button.

    I know that this can be done but I would like to have an exampel, like where do I write the code what offset must I use and basicly how do I change the way my overhead works.

    Im using FDS sys cards, with all xmls in place so all normal operations works just fine with my full PM suite.

  2. #2
    25+ Posting Member
    Join Date
    Dec 2008
    Location
    Norway
    Posts
    38
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Exclamation found some answers|

    Like AchillesP says in his post about fspassengers I must
    edit in xx.lgc file and in sysvar.txt file.

    So Its in sysvar I do the editing??
    "
    **You must delete the nosmoking and seatbelts logic that comes with pmsys737.lgc

    Insert inside sysvar.txt the below lines at the buttom of the file.
    "

  3. #3
    500+ This must be a daytime job
    Join Date
    Feb 2006
    Location
    N/A
    Posts
    511
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Pushback Panel V2.0 Program

    There is a program that was made for FS9 that did a great job of handling Pushback Operations with pre-recorded sound files. It also included angles of pushback (not just the 90 degree, but other smaller angles).

    This program was freeware and was called Pushback Panel v2.0 for Microsoft Flight Simulator 2004. This panel is based on XML gauges by Rob Barendregt. It is intended for Pushback operations.

    Goto this link for more information:

    http://harrierpanels.avsim.ru/eng/pb.html#pb2

    I do have the zip files for PB 2.0 and the zip file pb2os.zip (that is a patch) if you cannot locate them. The patch enables Pushback Panel v2.0 to use Wingfold command in FS2004 to toggle ON/OFF the Project Opensky Pushback truck ( PTS-1 ). The patch comes with a default bitmap (posky.bmp) of Project Opensky Boeing 767-300 V4 (Air Canada livery) that can be replaced with any other.

    Finally, I know FS9 programs can be made to work in FSX, so this would be a good one to figure out. Also, FSUIPC would then be setup with your Overhead switch/button to trigger the wingfold command and thus trigger the pushback panel.

    I've used this panel in FS9 and it worked fine, it just needs a way to be brought into FSX...

  4. #4
    25+ Posting Member
    Join Date
    Dec 2008
    Location
    Norway
    Posts
    38
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Thumbs up Tx

    ve a look at the this today and then if someone could be so kind to do an exampel code maybe im getting the hang of it

    Trevor have also posted offset for dummies, so this is starting slowly to look like a project.

Similar Threads

  1. FMC tutorial
    By cockpit737 in forum PM Boeing FMC/CDU
    Replies: 11
    Last Post: 04-14-2009, 04:50 PM
  2. FSX Tutorial
    By AchillesP in forum Computer Hardware Setup
    Replies: 4
    Last Post: 10-17-2008, 06:32 PM
  3. Mix Vernier Tutorial
    By AndyT in forum Cockpit Building Tutorials
    Replies: 0
    Last Post: 05-05-2008, 03:46 AM
  4. opencockpit tutorial?
    By imported_767300 in forum OpenCockpits General Discussion
    Replies: 4
    Last Post: 03-20-2008, 09:22 PM