Results 1 to 6 of 6
  1. #1
    10+ Posting Member motion2's Avatar
    Join Date
    Dec 2008
    Location
    Klamath Falls Oregon
    Posts
    13
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Total frustration/Legacy

    I am at my wits end here. Does anyone know where and how to set 'take-off trim 7' on Wilco's Legacy for FSX?

    Mike

  2. #2
    500+ This must be a daytime job


    Efe Cem Elci's Avatar
    Join Date
    Jan 2008
    Location
    Istanbul, Turkey, Turkey
    Posts
    544
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Have you tried setting the elevator trim indicator arrow on the far right display so that its in the green? Its marked pitch.

  3. Thanks motion2 thanked for this post
  4. #3
    10+ Posting Member motion2's Avatar
    Join Date
    Dec 2008
    Location
    Klamath Falls Oregon
    Posts
    13
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    The question would then be, how do you access/change the pitch setting to green? MIne stays yellow and virtually all tutorials I have read so far simply state 'set your pitch to 7'. I have programmed one of my yoke buttons through FSX-'pitch up' with no effect on this. Must be simple, but I'm missing something.

    Mike

  5. #4
    500+ This must be a daytime job


    Efe Cem Elci's Avatar
    Join Date
    Jan 2008
    Location
    Istanbul, Turkey, Turkey
    Posts
    544
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    How about trying the Elevator Up/Down controls? They should be 1 and 7 on the number pad by default.

  6. #5
    150+ Forum Groupie sas550's Avatar
    Join Date
    May 2007
    Location
    Sweden
    Posts
    236
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Under surface controls "Elevator trim up/down" or through Fsuipc (payware) buttons/fs controls "Elevator trim up/down"
    Regards Anders Eriksson


    www.simcockpit.se

    FS9

  7. Thanks motion2 thanked for this post
  8. #6
    10+ Posting Member motion2's Avatar
    Join Date
    Dec 2008
    Location
    Klamath Falls Oregon
    Posts
    13
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Red face

    Many thanks to those who helped. Seems that Legacy, (download version), was not seeing all the control inputs. A re-install of the program and reformat of the controls finally got this bird off the ground. Just completed a night flight from Las Vegas to home, KLMT.

    Thanks again!

    Mike

Similar Threads

  1. EMB Legacy..AHHHH Cessna
    By BlackWidow in forum My Cockpit Update
    Replies: 40
    Last Post: 12-27-2009, 11:27 PM
  2. www.frustration.com!!!
    By NigelD in forum I/O Interfacing and Hardware
    Replies: 0
    Last Post: 08-16-2009, 07:28 PM
  3. More measurement frustration
    By orwell84 in forum Where to Start Building a Home Cockpit
    Replies: 14
    Last Post: 12-23-2008, 02:03 PM
  4. frustration
    By 747sim in forum Phidgets & Cockpit Simulator Builder
    Replies: 13
    Last Post: 06-28-2008, 04:54 PM
  5. Phidget Frustration
    By AndyT in forum Phidgets & Cockpit Simulator Builder
    Replies: 5
    Last Post: 02-08-2007, 09:38 PM