Results 1 to 10 of 10
  1. #1
    150+ Forum Groupie
    Join Date
    Nov 2008
    Location
    Usa
    Posts
    163
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Servos instead of poteniometers?

    Hi all
    I am looking at different options to connect the cyclic, collective and pedals in my helicopter cockpit to the computer via a usb board .

    Instead of using poteniometers is it possible to use servos form say model aircraft but heavy duty ones, and if so what usb board would be recommend.

    Thanks

    Rhys

  2. #2
    No, You can use servos in conjuction with potentiometers for movement in autoflight but you still need pots to tell the software that a movement has been made.

    Gary

  3. #3
    25+ Posting Member
    Join Date
    Aug 2008
    Location
    UK
    Posts
    72
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Potentiometers are variable resistors and provide a signal TO the PC to tell it where the control is positioned. Servos are motors that take a signal FROM the PC to make something move.

    I am not certain that I understand what you want to achieve here.

    Skywatch

  4. #4
    150+ Forum Groupie
    Join Date
    Nov 2008
    Location
    Usa
    Posts
    163
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Thanks guys
    I am looking at the best options to connect the control rods on my helicopter cockpit to the computer usb port.
    My cockpit has a total of 5 control rods

    -2 rods control the cyclic, 1 for forward/back movement and 1 for left and right movement these two rods are in between the pilots/copilots seat in a horizontal position

    -2 rods for the pedals under the cockpit floor

    -1 rod in a vertical position for the collective

    I am looking at what would be the best option to get the controls to interface with the computer

    Cheers

    Rhys

  5. #5
    2000+ Poster - Never Leaves the Sim Michael Carter's Avatar
    Join Date
    Oct 2006
    Location
    Southern Illinois, USA
    Posts
    2,887
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    10K pots and any number of available input cards from Open Cockpits, Phidgets, FDS, Leo Bodnar, Hagstrom, etc, etc.

    It's up to you to design and engineer the linkage to hook your control rods to the pots, as well as anchor the pots in a mount of some sort that you design and build.
    Boeing Skunk Works
    Remember...140, 250, and REALLY FAST!

    We don't need no stinkin' ETOPS!



    Powered by FS9 & BOEING

  6. #6
    150+ Forum Groupie XOrionFE's Avatar
    Join Date
    Jan 2008
    Location
    Sugar Grove, IL
    Posts
    264
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Quote Originally Posted by Michael Carter View Post
    10K pots and any number of available input cards from Open Cockpits, Phidgets, FDS, Leo Bodnar, Hagstrom, etc, etc.

    It's up to you to design and engineer the linkage to hook your control rods to the pots, as well as anchor the pots in a mount of some sort that you design and build.
    Michael, out of curiosity, I have been using 100K pots. Is 10K better? do you get better resolution from one over the other? Just curious? I may be using the wrong type

    Scott

  7. #7
    1000+ Poster - Fantastic Contributor AndyT's Avatar
    Join Date
    Jun 2006
    Location
    Oahu, Hawaii
    Posts
    1,236
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    The type of Pot you use depends on how much juice you have in the circuit. 10K and 100K pots are pretty standard.
    10K = 10,000 Ohms of resistance
    100K= 100,000 Ohms of resistance
    God's in command, I'm just the Pilot.
    http://www.geocities.com/andytulenko/

  8. #8
    25+ Posting Member
    Join Date
    Aug 2008
    Location
    UK
    Posts
    72
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    100K pots are used in most joysticks as they were the standard for the 'game port' interface on soundcards and motherboards. Actually a 100K will use less current over 90% of it's range than a 10K one will. You would not know without looking at the pot which you have from the movement on the screen.

    As for the original question, the cheapest thing would be to get some cheap usb joysticks and use the circuit boards in them. Just keep the rest of them for the future and use your own new pots wired to the joystick boards.

    Skywatch

  9. #9
    2000+ Poster - Never Leaves the Sim Michael Carter's Avatar
    Join Date
    Oct 2006
    Location
    Southern Illinois, USA
    Posts
    2,887
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Quote Originally Posted by XOrionFE View Post
    Michael, out of curiosity, I have been using 100K pots. Is 10K better? do you get better resolution from one over the other? Just curious? I may be using the wrong type

    Scott

    Doesn't really matter. As Skywatch said, you can't tell the difference in operation or calibration. The only thing that really matters is linearity and accuracy or tolerance.
    Boeing Skunk Works
    Remember...140, 250, and REALLY FAST!

    We don't need no stinkin' ETOPS!



    Powered by FS9 & BOEING

  10. #10
    150+ Forum Groupie XOrionFE's Avatar
    Join Date
    Jan 2008
    Location
    Sugar Grove, IL
    Posts
    264
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    thanks guys

Similar Threads

  1. Servos
    By shearder in forum Where to Start Building a Home Cockpit
    Replies: 3
    Last Post: 02-21-2015, 06:08 AM
  2. USBexpension card and poteniometers
    By henri in forum I/O Interfacing Hardware and Software
    Replies: 2
    Last Post: 03-28-2011, 02:42 PM
  3. How Best to Power Servos?
    By FredK in forum Phidgets & Cockpit Simulator Builder
    Replies: 9
    Last Post: 05-17-2010, 08:37 PM
  4. Leo Bodnar board and Poteniometers
    By mach7 in forum MyCockpit Support:
    Replies: 9
    Last Post: 07-20-2009, 07:05 AM