Page 1 of 2 12 LastLast
Results 1 to 10 of 13

Thread: Static

  1. #1
    500+ This must be a daytime job Jackpilot's Avatar
    Join Date
    Dec 2005
    Location
    MONTREAL
    Posts
    930
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Static

    I have to bring back some computers in a carpeted room.
    Last year in the same room I fried a Hagstrom board with static (that horrible Tic at the end of my finger!!)

    Besides removing the carpet or grounding myself is there a way to prevent this ?
    Jackpilot
    B737-700 Posky
    FS9/P.Magenta
    without PMSystem

  2. #2
    500+ This must be a daytime job JBaymore's Avatar
    Join Date
    Mar 2005
    Location
    Wilton, New Hampshire USA
    Posts
    601
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Install a huimidifier in the room. High humidity keeps the static charge down. BUT.... it creates its own set of potential issues.

    best,

    ................john

  3. #3
    300+ Forum Addict Rodney's Avatar
    Join Date
    Nov 2005
    Location
    Colorado Springs, CO USA
    Posts
    332
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Make Your Own Anti-Static Spray

    Take an empty spray bottle (such as a window cleaner bottle) and pour in a small amount of fabric conditioner. Fill the bottle with water. The mixture should be about 30:1. Spray the car seats (furniture and/or carpets) and allow to dry. Reapply as necessary.
    Rodney -
    Real 727-200 pit
    Last Flown as N392PA
    FS9

  4. #4

    Airbus

    OR KEEP YOUR DAMN FINGERS OFF THE HAGSTROM BOARD!!! LOL

    Tim

  5. #5
    Heli Builder
    Join Date
    May 2008
    Location
    Earth
    Posts
    288
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    1. Take off your shoes.
    2. Look for a metal item somewhere near and touch it to release the static before touching the the board.
    3. Get a wrist strap which is grounded. The strap has a clip so you can just snap it on /off without removing the strap if you move a lot. These straps are not expensive. I learned that one from maintaining a Frasca 142 which has these installed by the factory.
    Fritz -> Helicopter Cockpit Builder
    (FSX | TH2Go | Arduino | Air Manager Avionics | CNC)

  6. #6
    75+ Posting Member Mr. Midnight's Avatar
    Join Date
    Mar 2006
    Posts
    117
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    static

    Unfortunately even with all the remedies given to you working on carpet is a sure way to generate static, I to had this problem in a carpeted room, even when I was just in the cockpit every now and then I would get shocked.

    Other than you taken out the carpet there is no way even with a humidifier will you not stop it, a lot or some you will still get it.

    What I did to absolutely stop it was to attach a long wire to a outlet screw , the ones that holds the faceplate on a metal box inside( because it is grounded), or attach it to any thing in the room that is grounded, even the case of a computer that you know is ground.

    Then run the wire under your carpet or place it where you cannot see the length of it, and if you fly all the time run it close to your chair or work place and when you begin to work just attach it to yourself, arm or lower leg.

    That has worked absolutely well for me.

    In the summer time I was fine but when it started getting cooler look out.

    Humidifiers work great but they do not cut down all of the static, especially if you decide to make some coffee and you have your socks on and forget that you were charging yourself.

    what i did later on was remove the capeting and put in wood flooring

    Hope this helps…………..Robert

  7. #7
    Heli Builder
    Join Date
    May 2008
    Location
    Earth
    Posts
    288
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Quote Originally Posted by Mr. Midnight View Post

    What I did to absolutely stop it was to attach a long wire to a outlet screw , the ones that holds the faceplate on a metal box inside( because it is grounded), or attach it to any thing in the room that is grounded, even the case of a computer that you know is ground.

    Then run the wire under your carpet or place it where you cannot see the length of it, and if you fly all the time run it close to your chair or work place and when you begin to work just attach it to yourself, arm or lower leg.
    Sounds like a great idea.

    Here is an image of the Anti-Static Wrist Band I was refering to earlier. Could use it in addition to the idea above by Mr. Midnight.

    Fritz -> Helicopter Cockpit Builder
    (FSX | TH2Go | Arduino | Air Manager Avionics | CNC)

  8. #8
    300+ Forum Addict Rodney's Avatar
    Join Date
    Nov 2005
    Location
    Colorado Springs, CO USA
    Posts
    332
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    If you can get your hands on a 6"x6" piece of flat copper, mount it to the wall, table, etc and run the ground wire to it. Touch it as you enter the room and most definatley before you touch anything. We used this method in the USAF and it worked well. An open computer case that is plugged in works too. Also, did you know that paper is a great static generator? Don't place your items on it. I learned that one the hard way.
    Rodney -
    Real 727-200 pit
    Last Flown as N392PA
    FS9

  9. Thanks Jackpilot thanked for this post
  10. #9
    500+ This must be a daytime job Jackpilot's Avatar
    Join Date
    Dec 2005
    Location
    MONTREAL
    Posts
    930
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Thanks guys...think I will remove the carpet for a wooden floor..another consequence of simbuilding...and use the wrist band in the meantime.
    Jackpilot
    B737-700 Posky
    FS9/P.Magenta
    without PMSystem

  11. #10
    500+ This must be a daytime job


    Efe Cem Elci's Avatar
    Join Date
    Jan 2008
    Location
    Istanbul, Turkey, Turkey
    Posts
    509
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    If you're set on removing the carpet (and feel it is a sacrifice) you could always look into anti-static carpeting as a solution. Was going to suggest it earlier but I assumed you were looking for a solution in the current setup as opposed to one that involved some alterations and additional spending.

Page 1 of 2 12 LastLast