Results 1 to 10 of 23
-
10-08-2008, 02:31 PM #1
opencockpits usb output card prob?
hi all problems problems problems ... everything i get just never works!!
at first ... then i learn about it !! hehe
all i can say thank god for this forum ............
here's the problem i have just brought your usb output card from opencockpits. when i run the test software " test usb output.exe"
firstly the five boxes at the top of the software rotate non stop with numbers? is that right?
secondly i have connected some leds from my fmc to the ground on the usb card and the postive to 59 - 63 . but they dont work when i click "all on " with the software. but when i connect the postive to the postive terminal next to the ground terminal on the usb card the led lights!. is that also right ?
my kit so far.!!!
gf mcp - working
op efis - working
gf 737 rudder - working
fmc - keys working ... no screen or leds yet...
thanks john d
-
10-08-2008, 02:38 PM #2
Yes. The USB outputs card works with a common + and all the outputs are separate grounds. That is quite opposite from the Master Card which works with a common GND and separate +5 V outputs.
Note that the common + for the USB output card can be set to 5V but also to higher voltages; for leds I recommend to use 5V
Nico
-
10-08-2008, 03:44 PM #3
ok nico that kind on makes sense i think i have got the wiring wrong on the fmc.
. i have all of the gnd connected together but with the resistor on the negative side of the led.
can you tell me the correct way to wire an led and resistor.
many thanks
john d
-
10-08-2008, 04:18 PM #4
Hi,
USB card settings:
connect +5V and gnd to the POWER connector (NOT the external option)
JMP1: OPEN
JMP2: CLOSED
Connect POWER terminal (second one from the bottom right) to a resistor;
connect resistor to + side of led;
connect - side of led to one of the outputs, say # 63 (next to the POWER Terminal
regards,
Nico
-
10-08-2008, 04:28 PM #5
ok i understand now .but can i connect the power terminal to lets say 4 resistors but bring the negative back per wire . so i mean can use one feed from the power terminal? also a newbie question dies it matter which way round the resistors go? i think thats every thing..... hehe
this is going to be long haul !!!!
thanks nico
regards john d
-
10-08-2008, 04:40 PM #6
-
Post Thanks / Like - 1 Thanks, 0 Likes, 0 Dislikes
jonnydaz53 thanked for this post
-
10-08-2008, 04:50 PM #7
does it matter which way round the resistors go?
regards john d
-
10-08-2008, 04:56 PM #8
No.
It also does not matter whether you put the resistor in the + lead of the resistor (between power and resistor) or in the - lead (between GND and resistor), as long as you put a resistor in series.
Nico
-
10-08-2008, 06:50 PM #9
-
Post Thanks / Like - 1 Thanks, 0 Likes, 0 Dislikes
kiek thanked for this post
-
10-09-2008, 02:10 AM #10
i have put 1 resistor per led. have i done it right?
regards john d
Similar Threads
-
Which output card for homebuilt steam instruments?
By AK Mongo in forum I/O Interfacing Hardware and SoftwareReplies: 6Last Post: 02-13-2011, 03:39 PM -
OC USB output card
By 150245 in forum OpenCockpits General DiscussionReplies: 8Last Post: 05-17-2010, 04:24 PM -
opencockpits master card j2 output qestion
By spiro in forum OpenCockpits General DiscussionReplies: 1Last Post: 11-05-2009, 03:33 PM -
Open Cockpits Output Card
By Michael Carter in forum I/O Interfacing Hardware and SoftwareReplies: 7Last Post: 01-12-2009, 10:26 AM -
Which Input/Output Card
By Holclo in forum I/O Interfacing Hardware and SoftwareReplies: 9Last Post: 02-27-2008, 07:30 AM
Candid connections: Platform for casual relationships Live Women Prime Сasual Dating
Super Сasual Dating - Genuine...