Results 1 to 5 of 5
  1. 09-27-2008, 03:32 PM #1
    Kain
    Kain is offline
    Our new friend needs to reach 10 posts to get to the next flight level
    Join Date
    Sep 2008
    Location
    USA
    Posts
    7
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Spur Gear questions

    I was wondering if gear teeth can be made as small as 0.015625 an inch in tooth thickness?

    Also is it possible to have a gear with only 4 teeth?
    Reply With Quote Reply With Quote
  2. 09-27-2008, 05:38 PM #2
    AndyT
    AndyT is offline
    1000+ Poster - Fantastic Contributor AndyT's Avatar
    Join Date
    Jun 2006
    Location
    Oahu, Hawaii
    Posts
    1,236
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Only 4 teeth? Hmm... I'm not sure that would even be considered a gear. Its interaction level with another gear would be intermittant at best. If you could give us a basic sketch of what it is your trying to build I'm sure we could help.
    God's in command, I'm just the Pilot.
    http://www.geocities.com/andytulenko/
    Reply With Quote Reply With Quote
  3. 09-27-2008, 06:13 PM #3
    Kain
    Kain is offline
    Our new friend needs to reach 10 posts to get to the next flight level
    Join Date
    Sep 2008
    Location
    USA
    Posts
    7
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Another question: Can a gear be made of 8 teeth with the tooth thickness being 0.03125 inch with a pitch diameter of 0.159 inch
    Reply With Quote Reply With Quote
  4. 10-22-2008, 08:13 PM #4
    rjfon1
    rjfon1 is offline
    10+ Posting Member
    Join Date
    Aug 2008
    Location
    Melbourne Australia
    Posts
    19
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Kain,
    Try this site. They make miniature gears. Not with as few as four teeth, but with a couple of gears you can get the right ratio. As you can see by the opening page they can make VERY small gears, and most are stock. I'll be using them for my gauges.
    http://www.marswell.com/Product.htm
    Rob,
    Mebourne Australia.
    Reply With Quote Reply With Quote
  5. 10-22-2008, 08:33 PM #5
    Jackpilot
    Jackpilot is offline
    500+ This must be a daytime job
    Tutorial Contributor / Point Value: 10
    Total Awards: 1
    Total Points: 10
    Jackpilot's Avatar
    Join Date
    Dec 2005
    Location
    MONTREAL
    Posts
    930
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Quote Originally Posted by Kain View Post
    I was wondering if gear teeth can be made as small as 0.015625 an inch in tooth thickness?

    Also is it possible to have a gear with only 4 teeth?
    Kain
    Where did you get those numbers and what are you trying to achieve????
    Is it a joke??
    Jackpilot
    B737-700 Posky
    FS9/P.Magenta
    without PMSystem
    Reply With Quote Reply With Quote
« Previous Thread | Next Thread »

Similar Threads

  1. Gear LED's
    By Clive in forum I/O Interfacing and Hardware
    Replies: 5
    Last Post: 04-09-2011, 02:38 AM
  2. Spur Gears CNC
    By riche543 in forum CNC Discussion
    Replies: 4
    Last Post: 12-04-2010, 10:42 AM
  3. Spur gears for 737 TQ
    By Sharpedge in forum Where to Start Building a Home Cockpit
    Replies: 8
    Last Post: 02-01-2008, 11:59 AM
  4. gear up gear down
    By Radar in forum Where to Start Building a Home Cockpit
    Replies: 47
    Last Post: 04-14-2007, 01:00 AM
  5. Gear instructions
    By michelmvd in forum FS2Phidget Users
    Replies: 6
    Last Post: 03-14-2007, 09:19 AM