New PM builds available - 07 Aug 08

[carlos hermida]

Have tested all new updates and here are some little problems with my setup:

1. Overhead annunciators doesn't light up (bright or dim) for both engines
- ENG VALVE CLOSED and SPAR VALVE CLOSED

PS: This happens with my OVHD hardware (graphic mode iluminates normal), need to know if any offset was changed for this or if it is related to pmsystems or pmGC, see below.

2. Same for EICAS yellow anunciators, none of then below light up for both engines.
- START VALVE OPEN, OIL FILTER BYPASS only LOW OIL PRESSURE goes up

3. MCP IAS/MACH now blinks "8" on first left digit, only stop blinking after setting IAS to 160 knots. This is a SPEED CONDITION SYMBOL for overspeed Vmo, Landing gear or flap limit as i know or i am wrong with something?, in this case if i set V2 speed for take off it goes blinking until reach 160 knots....

4. on EICAS i have no smooth operation of WHITE N1 comand by thrust lever position, it goes up and down like STEPs when i move thrust lever.

Until now this are my reports, i think that all other issues has gone.....

1==>THIS WAS SOLVED AFTER CHECK THAT THERE IS IN PMSYSTEMS USER OPTIONS MENU A ITEM TO SET (TICK) VALVES - values - 0-2-1, i.e. for SPARVALVE1 use SPARVAL1

2==>SOLVED TOGETHER WITH UPPER SOLUTION.

3==> This is a new feature implemented by Enrico, see page 111 of "737 cockpit companion".

4==> Will need to recalibrate throttle to check if it will work smoothly, because downgrading to my last build used it worked again...

[carlos hermida]

Its like Christmas !!!

Yes, all CDU (old, RTE,LEG,STAR, AIRWAY) problems are history

but:

1. I have now problems to fly in machmode without VNAV
If I tune .80 in the CPFlight MCP, the speedtape always jump to .73
with kts it works perfect ...

2. I am missing the TAI indication on EICAS at the N1 display, when ANTI ICE is on!

Can you pls confirm same bug, before I report to PM?
Thanks
Jan

Hi Jan,

About ANTI-ICE i needed to setup again this offset for my hardware (i am using INTERFACEIT cards from FDS) , so after that it worked correctly again and TAI is there

[Ray Proudfoot]

One issue is still outstanding. When climbing I always engage FLCH and as the aircraft passes the altitude set in the MCP.INI for the switchover from SPD to Mach this is changed on the MCP.

However, during descent I stay in VNAV mode but the speed does not switch from Mach to SPD at the stored MCP.INI altitude resulting in an overspeed. Would more experienced pilots agree this is a bug that should be corrected? This occurs in both FS9 and FSX.

The other issue still outstanding is the turning-in towards waypoints when within 3 miles. Despite sending another message to support 9 days ago I have not yet received a reply. This issue only affects FSX.

[Daniel Schiffer]

Hello,

1==>THIS WAS SOLVED AFTER CHECK THAT THERE IS IN PMSYSTEMS USER OPTIONS MENU A ITEM TO SET (TICK) VALVES - values - 0-2-1, i.e. for SPARVALVE1 use SPARVAL1

2==>SOLVED TOGETHER WITH UPPER SOLUTION.

3==> This is a new feature implemented by Enrico, see page 111 of "737 cockpit companion".

4==> Will need to recalibrate throttle to check if it will work smoothly, because downgrading to my last build used it worked again...

sorry but i have not the 737 Cockpit companion
can somebody explain How that function with the blinking "8" in the MCP Speed?

Thx

Daniel

[paulj]

From 737 cockpit companion
"Speed Condition Symbols"
. Overspeed or Underspeed limiting symbol appears when commanded speed cannot reached.

.Flashing 8 symbol means overspeed of Vmo/Mmo, landing gear,or flaps limit.
.Flashing A (alpha, for AOA) symbol means underspeed:below minimum speed(as sensed from angle of attack) or V/S mode performance reversion (airspeed becomes 5k less then MCP selected speed and there is no acceleration.

hope that makes sense to you...

Paul

[Daniel Schiffer]

Thank you Paul for the infos.

mmh.... i become flashing "A" if my speed overthe max Speed(not below Minimum Flaps seed for seting Flaps. And the "8" flashing permanent if my Speed seting below 160 kts. is that correct?

Or little but from PM


Regards


Daniel

[Jan Pemöller]

Ok, Thomas from PM told me that TAI indications are working correct!
So I will check my system ...

[Jan Pemöller]

Hello,



sorry but i have not the 737 Cockpit companion
can somebody explain How that function with the blinking "8" in the MCP Speed?

Thx

Daniel

me too, is it somewhere available or posible to download ???

[carlos hermida]

Hi Jan,

Here you have a link to buy it, i recommend you the FMC guide, too.

http://fmcguide.com/StoreFront.bok

[touwersl]

Maybe a silly question from my side but I can't find these builds on the PM site. The latest official builds date from 170708?????

Did I mis something here?

Latest official builds gc456 mcp428 cdu398 ... a BIG THANK YOU

I did several test routes with the latest builds ( routes mentioned earlier here on the forum - EBOS/EDDP - EBOS/LSGG - EBOS/LFPG (lots of STARs)
and the problems with portions of the route dissapearing when entering the STAR or RWY's
are gone !!!
Aircraft and CDU are behaving as they should during entering new STAR's or RWY's aswell


In the GC a lot of special B744 stuff as been incorporated aswell the possibilty not to show wind dir / speed on the ground .

In real life this is also the case, as wind dir / speed is a calculated item by FMC on base of offset Route / drift etc.

So all together these builds are a great progress and Enrico did big efforts to let it all work smoothly.

I can't speak for the B737

A big thank you to Enrico and PM

B. Rgds

Michel