Results 1 to 5 of 5

Thread: Building a Yoke

  1. 10-27-2007, 08:03 AM #1
    cpt kaneo
    cpt kaneo is offline
    10+ Posting Member
    Join Date
    Oct 2007
    Location
    Australia
    Posts
    14
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Building a Yoke

    Does anyone have any experience in making Yokes because I am looking for a circuit diagram of the electronics needed.

    Any information would be greatly appreciated

    thanks in advance

    Kane
    Reply With Quote Reply With Quote
  2. 10-27-2007, 10:07 AM #2
    Michael Carter
    Michael Carter is offline
    2000+ Poster - Never Leaves the Sim Michael Carter's Avatar
    Join Date
    Oct 2006
    Location
    Southern Illinois, USA
    Posts
    2,887
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    There are four switches on a Boeing yoke. Dual momentary trim switches (ON) OFF (ON), A single momentary pushbutton NC switch for the AP disconnect, and a momentary NO PTT switch. They are wired the same as any other simple switch.

    Here is the schematic for the trim switches:

    Boeing Skunk Works
    Remember...140, 250, and REALLY FAST!

    We don't need no stinkin' ETOPS!



    Powered by FS9 & BOEING
    Reply With Quote Reply With Quote
  3. 10-27-2007, 10:38 PM #3
    cpt kaneo
    cpt kaneo is offline
    10+ Posting Member
    Join Date
    Oct 2007
    Location
    Australia
    Posts
    14
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    thanks a lot!
    Reply With Quote Reply With Quote
  4. 10-28-2007, 05:40 AM #4
    Westozy
    Westozy is offline
    MyCockpit Support Staff
    Builder Of The Month / Point Value: 100
    Total Awards: 1
    Total Points: 100



    Westozy's Avatar
    Join Date
    Nov 2005
    Location
    Perth, Western Australia
    Posts
    1,415
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Hi Kane, my 737 yokes are homemade, there are heaps of pics in my gallery!

    Gwyn

    737NG using Prosim737, Immersive Calibration Pro, Aerosim Solutions motorized TQ & cockpit hardware, CP Flight MCP & FDS SYS1X, SYS2X & SYS4X, FDS PRO FMCs, AFDS units & Glarewings, Matrix Orbital ELEC display, Pokeys Landing & Cruise alt display, Buttkicker Gamers, 3 x BenqMW811ST projectors with a Matrox Th2Go
    http://www.aerosimsolutions.com.au
    Supporter of MyCockpit.org, please join me in donating!!!
    Reply With Quote Reply With Quote
  5. 10-29-2007, 02:06 AM #5
    cpt kaneo
    cpt kaneo is offline
    10+ Posting Member
    Join Date
    Oct 2007
    Location
    Australia
    Posts
    14
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Thanks Gwyn, I'll make sure that I check them out

    kane
    Reply With Quote Reply With Quote
« Previous Thread | Next Thread »

Similar Threads

  1. Building a yoke
    By Mechanic_Man in forum Where to Start Building a Home Cockpit
    Replies: 5
    Last Post: 11-10-2010, 11:13 AM
  2. Cockpit Building, nah......it's all about Airport Building!
    By CessnaGuy in forum Pilots Lounge - Let your Hair down
    Replies: 3
    Last Post: 07-08-2010, 06:43 AM
  3. Cessna Yoke Column - Yoke Movement ?
    By Ronson2k9 in forum General Aviation (GA) Builder Disccusion
    Replies: 2
    Last Post: 04-20-2010, 12:09 PM
  4. Need help building a GA flight yoke?
    By CessnaGuy in forum Westozy's Mechanical Engineering
    Replies: 5
    Last Post: 02-28-2009, 06:48 AM
  5. yoke building
    By spiro in forum General Builder Questions All Aircraft Types
    Replies: 2
    Last Post: 02-14-2009, 02:57 PM