Results 1 to 4 of 4
  1. #1
    150+ Forum Groupie ak49er's Avatar
    Join Date
    Jan 2007
    Location
    Big Lake, Alaska
    Posts
    281
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Unhappy Annoying Recurring Tone in 737

    So, last night I took a nice nighttime IFR flight from Pheonix Sky Harbor to Dallas Fort Worth, I set up my flight plan, obtained clearance and set out on my journey. After a bumpy climb, I settled out to cruise and performed a final check. While looking at charts halfway throught my flight, a Morse code like tone started repeating every several seconds or so out of my left speaker. I checked all avionics and panels but could not see a corresponding light flash in sequence with the repeating tone. I turned off my avionics and it stopped. I retuned the radios but still the tone kept repeating every several seconds. I thought it might be a SELCAL message code but this plane (THE 737 Experience) is not equipped for SELCAL. I remember this problem from the default 737-400 from FS9. Needless to say this tone grew annoying and I ended my flight with the sound turned off. Does any one know what this tone is simulating and how to acknowledge it or turn it off? This dampened the experience of an other wise flawless flight.

  2. #2
    1000+ Poster - Fantastic Contributor Bob Reed's Avatar
    Join Date
    Oct 2005
    Location
    Holley, New York U.S.A.
    Posts
    1,776
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    That is the VOR ident. You tuned your VOR radios and one of them was told to id the VOR. The morse code you get confirms you are tuned to the proper one. Turn ident off on that vor radio.
    Bob Reed

  3. #3
    2000+ Poster - Never Leaves the Sim Michael Carter's Avatar
    Join Date
    Oct 2006
    Location
    Southern Illinois, USA
    Posts
    2,887
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Now that you know what it is, you can use it on your flights.

    Each time a nav-aid is tuned it is suppose to be positively identified using that Morse code you are hearing. After ID'ing the station, you can then turn it off.

    The Morse identifier is on charts in a box near the station. Sometimes with an arrow from the box pointing to the station if it's not obvious. In congested airspace with a lot of stations close together, the ID box might be a couple of inches away with that arrow.

    It is possible to receive the wrong station on the right frequency depending upon your distance from each. That is why it is important to positively identify the station you are using to navigate.
    Boeing Skunk Works
    Remember...140, 250, and REALLY FAST!

    We don't need no stinkin' ETOPS!



    Powered by FS9 & BOEING

  4. #4
    150+ Forum Groupie ak49er's Avatar
    Join Date
    Jan 2007
    Location
    Big Lake, Alaska
    Posts
    281
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Thank-you very much, this issue is finally put to rest. I can't wait to try it out tonight.

Similar Threads

  1. 737NG A/P Disconnect Tone
    By ian@737ng.co.uk in forum General Builder Questions All Aircraft Types
    Replies: 6
    Last Post: 07-30-2008, 07:57 PM
  2. PM Sounds and 'Cavalry Charge' Tone
    By Tomlin in forum PM General Q & A
    Replies: 5
    Last Post: 06-30-2008, 04:42 PM