Page 1 of 2 12 LastLast
Results 1 to 10 of 12
  1. #1
    MyCockpit Support Staff


    Westozy's Avatar
    Join Date
    Nov 2005
    Location
    Perth, Western Australia
    Posts
    1,415
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Announcing new product! Yoke mounting mechanism

    Hi all,
    First of all thanks to everyone that has been contacting me via my new website, the interest has really surprised me and I am grateful for the growth in business! The announcement of my column base mechanism lead to questions from quite a few members asking me if I can produce an elbow for the top of the column. I thought this was a good idea for another product so I have completed a design and can now offer the units for sale to our members.

    The unit consists of a solid Trovidur PVC circular block machined to house a high quality needle roller bearing for the hollow axle. The hollow axle will allow yoke button wiring to be be fed down the inside of the yoke column along with the potentiometer wires which are supplied. The flange has two rows of threaded holes for mounting a replica or generic yoke handle. The flange also has a pin for limiting rotation to 180 degrees. The potentiometer drive for roll motion is geared at 3:2 so the potentiometer rotates 270 degrees. There is a small pulley on the rear of the unit with a locking device to grip 2 mm wire rope, this is for transmitting roll motion across to the second yoke in a two position simulator. The mechanism will slide into a standard 80mm PVC drain elbow which can also be supplied if required. Pitched at an introductory starting price of AUD$280.00 per unit. Combined with the yoke base mechanism the package represents a low cost solution for building a high quality relica Boeing type yoke control column with pitch and roll potentiometers ready to wire to your interface card.


    Yoke-head-05..gif
    Yoke-head-02..gif
    Yoke-head-03..gif
    Yoke-head-04..gif
    Yoke-head-01..gif

    Cheers,
    Gwyn Perrett
    www.aerosimsolutions.com.au
    Last edited by Westozy; 04-28-2010 at 10:42 PM.

    737NG using Prosim737, Immersive Calibration Pro, Aerosim Solutions motorized TQ & cockpit hardware, CP Flight MCP & FDS SYS1X, SYS2X & SYS4X, FDS PRO FMCs, AFDS units & Glarewings, Matrix Orbital ELEC display, Pokeys Landing & Cruise alt display, Buttkicker Gamers, 3 x BenqMW811ST projectors with a Matrox Th2Go
    http://www.aerosimsolutions.com.au
    Supporter of MyCockpit.org, please join me in donating!!!

  2. #2
    25+ Posting Member jsfboat's Avatar
    Join Date
    Jan 2010
    Location
    Sebastian, Florida
    Posts
    54
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Re: Announcing new product! Yoke mounting mechanism

    Is this only for replica yokes, or will it work for authentic ones as well?

  3. #3
    MyCockpit Support Staff


    Westozy's Avatar
    Join Date
    Nov 2005
    Location
    Perth, Western Australia
    Posts
    1,415
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Re: Announcing new product! Yoke mounting mechanism

    Quote Originally Posted by jsfboat View Post
    Is this only for replica yokes, or will it work for authentic ones as well?
    Hi, I don't have access to a genuine yoke but I am sure it could be made to adapt. I believe the real thing has a protruding shaft with an internal spline. If I had an accurate drawing of the real yoke I could make an adaptor to suit it. My own simulator has replica fibreglass yokes from Roberto at www.throttletek.com and these would easily adapt to my flange mechanism, this is what I based the design around. Could you please post a picture of the rear of your real yoke handle or email it to me at gwyn737 (at) live.com.au, that would be appreciated and I could design an adaptor for it!

    Regards,

    Gwyn

    737NG using Prosim737, Immersive Calibration Pro, Aerosim Solutions motorized TQ & cockpit hardware, CP Flight MCP & FDS SYS1X, SYS2X & SYS4X, FDS PRO FMCs, AFDS units & Glarewings, Matrix Orbital ELEC display, Pokeys Landing & Cruise alt display, Buttkicker Gamers, 3 x BenqMW811ST projectors with a Matrox Th2Go
    http://www.aerosimsolutions.com.au
    Supporter of MyCockpit.org, please join me in donating!!!

  4. #4
    Boeing 777 Builder


    Kennair's Avatar
    Join Date
    Jan 2007
    Location
    Perth, Western Australia
    Posts
    730
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Re: Announcing new product! Yoke mounting mechanism

    Great work Gwyn. Your day job is going to become a liability at this rate.

    Just a question though. In a two yoke setup you wouldn't need the gearing and pot on the other side, just the axle mechanism. Same with your yoke pivot mech. Will these be available as separate products, or will you just purchase two of each of the above units and not utilize the pots on one side?

    Ken.

    Hi Ken,
    Correct! The 'co pilot's' side of both products do not need the additional pot so I would probably leave it out and I would reduce the cost accordingly.
    I also completed your TQ baseplate and attached it to the lever mechanism, it's ready to have the box built on it now!

    Cheers Gwyn
    Last edited by Westozy; 04-27-2010 at 01:18 AM.
    Opencockpits | Aerosim Solutions | Sim-Avionics | P3D | FDS | FTX | AS16 | PPL | Kennair


  5. #5
    Boeing 777 Builder


    Kennair's Avatar
    Join Date
    Jan 2007
    Location
    Perth, Western Australia
    Posts
    730
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Re: Announcing new product! Yoke mounting mechanism

    Fantastic Gwyn,

    Can I see the handiwork tomorrow?

    Ken.
    Opencockpits | Aerosim Solutions | Sim-Avionics | P3D | FDS | FTX | AS16 | PPL | Kennair


  6. #6
    300+ Forum Addict



    Join Date
    Mar 2009
    Location
    Body in Netherlands, Hart in the Fairest Cape!
    Posts
    387
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Re: Announcing new product! Yoke mounting mechanism

    Excellent work good fellow, ... I'll be ordering a set of these, ... could you please find out about postage to Europe for me.

    Cheers,

    Andrew.

  7. #7
    MyCockpit Support Staff


    Westozy's Avatar
    Join Date
    Nov 2005
    Location
    Perth, Western Australia
    Posts
    1,415
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Re: Announcing new product! Yoke mounting mechanism

    Quote Originally Posted by Kennair View Post
    Fantastic Gwyn,

    Can I see the handiwork tomorrow?

    Ken.
    I'll bring it along....Gwyn

    737NG using Prosim737, Immersive Calibration Pro, Aerosim Solutions motorized TQ & cockpit hardware, CP Flight MCP & FDS SYS1X, SYS2X & SYS4X, FDS PRO FMCs, AFDS units & Glarewings, Matrix Orbital ELEC display, Pokeys Landing & Cruise alt display, Buttkicker Gamers, 3 x BenqMW811ST projectors with a Matrox Th2Go
    http://www.aerosimsolutions.com.au
    Supporter of MyCockpit.org, please join me in donating!!!

  8. #8
    MyCockpit Support Staff


    Westozy's Avatar
    Join Date
    Nov 2005
    Location
    Perth, Western Australia
    Posts
    1,415
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Re: Announcing new product! Yoke mounting mechanism

    Quote Originally Posted by capetonian View Post
    Excellent work good fellow, ... I'll be ordering a set of these, ... could you please find out about postage to Europe for me.

    Cheers,

    Andrew.
    Will do......Gwyn

    737NG using Prosim737, Immersive Calibration Pro, Aerosim Solutions motorized TQ & cockpit hardware, CP Flight MCP & FDS SYS1X, SYS2X & SYS4X, FDS PRO FMCs, AFDS units & Glarewings, Matrix Orbital ELEC display, Pokeys Landing & Cruise alt display, Buttkicker Gamers, 3 x BenqMW811ST projectors with a Matrox Th2Go
    http://www.aerosimsolutions.com.au
    Supporter of MyCockpit.org, please join me in donating!!!

  9. #9
    10+ Posting Member weshollett's Avatar
    Join Date
    Aug 2007
    Location
    Perth WA
    Posts
    24
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Re: Announcing new product! Yoke mounting mechanism

    Another must have product.

  10. #10
    Boeing 777 Builder


    Kennair's Avatar
    Join Date
    Jan 2007
    Location
    Perth, Western Australia
    Posts
    730
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Re: Announcing new product! Yoke mounting mechanism

    Quote Originally Posted by Westozy View Post
    I'll bring it along....Gwyn
    I just have to steal this thread a little to comment on my 777 throttle quad. Just had a play with it tonight and it is sweeeeeeeeeeeet!!! Wait till you see pictures of the finished product, its just too bad most of you won't get a chance to actually feel it. Quality to say the least. Also had a play with the yoke elbow mechanism and it will certainly revolutionise the sim building community.

    Great stuff Gwyn.

    Ken.
    Opencockpits | Aerosim Solutions | Sim-Avionics | P3D | FDS | FTX | AS16 | PPL | Kennair


  11. Thanks Westozy thanked for this post
Page 1 of 2 12 LastLast

Similar Threads

  1. Announcing open beta of new full 737 suite for cockpit builders
    By metamarty in forum General Builder Questions All Aircraft Types
    Replies: 1
    Last Post: 08-30-2010, 07:28 AM
  2. Announcing new product! Yoke base pivot
    By Westozy in forum Westozy's Mechanical Engineering
    Replies: 13
    Last Post: 04-21-2010, 03:33 AM
  3. Announcing new product!!! - A340 throttle quadrant
    By Westozy in forum Westozy's Mechanical Engineering
    Replies: 7
    Last Post: 02-17-2010, 02:49 AM
  4. Yoke mechanism progress
    By ivar hestnes in forum My Cockpit Update
    Replies: 9
    Last Post: 08-28-2008, 04:23 PM