OK, but I'm not near destination. I'm just entering cruise phase! I think is too early for that message.
Printable View
Hi Leonidas,
1. The MCDU and the ECAM are not linked. So it cannot know if you decided to do F1 or F2 takeoff.
2. This happens when you're less than 200NM from destination.
3. Cannot reproduce this one. You did set bopth pressed and released events on this button?
regards
JL
Each button has two states pressed (you're pushing the button with your finger) and released (you're no longer pushing with your finger). For the same action (take over button for example).
JL
For all you guys, who like that Navigraph supports Jeehell in the future with the Airacs... and make a little pressure to Navigraph!
I opened a Thread where you can ask Navigraph to support Jeehell in future. Looking forward, if some of you here support this Thread. ;)
Regards
Florian
I set both to CPT_APTO, try once and It seems to be OK for now. Thanks.
Let me tell you another minor issue about ground power button on OVHD panel. This has two potitions: OUT (where green AVAIL lights up when you select EXT PWR from addons) and IN (where blue ON lights up when you push it to get that power). But in my case (and just for that button), the state changes when I push it IN and doesn't change when I push it OUT. So, I should press twice in order to change from AVAIL to ON and vice versa! I've tried all these options on picture, but nothing changed. I use FDS card.http://www.mycockpit.org/forums/atta...id=10432&stc=1
I have also one question about EXTERNAL POWER: Is there any way to activate the external power without using the P3D menu?
Thanks
Stefan
@Leonidas: in the real ACFT, this switch is spring loaded: it cannot stay pushed down...
@Stefangr: look for the fsuipc offsets
Hallo JL,
today i try to implemet the F/O RMP but had some problems.
The Following:
*For the Captainside i use the RMP from Opencockpits with the EHID Modul
*The F/O Side is selfbuild and programmed via the SIOC_Creator
So far so good. I had the problem that i cant adjust the Frequencies of the F/O RMP. The Encoder works in the SIOC Monitor and there was no problem. But when i change the Frequencies on the CPT. RMP the Frequencies on the F/O Side also changed. Is this normal?
I discovered also two bugs in the SIOC_Creator.
1. SIOC_Creator doesn´t save the IDX for the F/O MCDU. I must submit everytime again after I open the saved config.
2. I have the following script for my LED BAR´s in the FCU. You remember?
When i push "Apply Configuration" SIOC-Creator says:Quote:
Var 1000, name LVLCH_BAR_ONE, Link IOCARD_DISPLAY, Device 1, Digit 65, Numbers 1{
&LVLCH_BAR_TWO = &LVLCH_BAR_ONE
&LVLCH_BAR_THREE = &LVLCH_BAR_ONE
}
Var 1001, name HDG_BAR, Link IOCARD_DISPLAY, Device 1, Digit 79, Numbers 1
Var 1002, name TK_BAR, Link IOCARD_DISPLAY, Device 1, Digit 64, Numbers 1
Var 1003, name SPD_BAR, Link IOCARD_DISPLAY, Device 1, Digit 77, Numbers 1
Var 1004, name MACH_BAR, Link IOCARD_DISPLAY, Device 1, Digit 78, Numbers 1
Var 1005, name HDGVS_BAR, Link IOCARD_DISPLAY, Device 1, Digit 66, Numbers 1
Var 1006, name TKFPA_BAR, Link IOCARD_DISPLAY, Device 1, Digit 67, Numbers 1
Var 1007, name VS_BAR, Link IOCARD_DISPLAY, Device 1, Digit 70, Numbers 1
Var 1008, name FPA_BAR, Link IOCARD_DISPLAY, Device 1, Digit 71, Numbers 1
Var 1009, name LVLCH_BAR_TWO, Link IOCARD_DISPLAY, Device 1, Digit 68, Numbers 2
Var 1010, name LVLCH_BAR_THREE, Link IOCARD_DISPLAY, Device 1, Digit 69, Numbers 1
Ok, then i delete the Lines "&LVLCH_BAR_THREE = &LVLCH_BAR_ONE" in VAR 1000 and the complete VAR 1010. Press the Apply Button and it works. After this I add the deleted rows again press again Apply and it works too. Thats a little bit strange! Do you have a Idea about this?Quote:
Phase 2ERROR! -
Line: 1081 Var 1010, name LVLCH_BAR_THREE, Link IOCARD_DISPLAY, Device 1, Digit 69, Numbers 1
==> LVLCH_BAR_THREE
%FAILED%
King regards
Florian
@stefangr
Copied from Jeehell's post #149Quote:
@Romeow: look at 78ED value 33 ...
Regards
René