Strange LED behavior

Hi,

I am quite a newbie in JeeHell in SIOC. That's the reason why I start step by step with my overheadpanel (AntiIce Panel) to build up a fixed based A320 (once upon...)

I use:

- OC USB Extention J1 <> OC MasterCard P1
- OC USB Outputs <> Out 63 LED

My first SIOC configuration was to get LED 63 lighted if APU Availible LED is on.

That's my config:

Code:

// *****************************************************************************// * Config_SIOC ver 4.5 - By Manuel Velez - www.opencockpits.com // ***************************************************************************** // * FileName : sioc.txt // * Date : 09.10.2013 Var 0001, name APUmasterSW, Link IOCARD_SW, Device 1, Input 1

For testing I press:

1) Both BAT switches at the Jeehell Overhead Panel (Software)
2) APU Master Switch
3) APU Start Switch

After pressing APU Master Switch LED 63 is getting lighted and I don't understand why...
After APU Start Switch is pressed LED 63 turned off until AVAIL is on (then LED 63 turns on again)...

I am a bit confused.

I changed allready LED 63 to another output to avoid a defective output but same behaviour with another output.

My SIOC.INI:

Code:

[ fichero de configuracion para el SIOC ver. 4.5 ] [ Configuration file for SIOC ] [************** SIOC ***************] [ Nombre asignado al SIOC ] [ SIOC name ] Name=Main [ Puerto del servidor IOCP ] [ IOCP port ] IOCP_port=8092 [ Tiempo de respuesta máximo de los paquetes IOCP ] [ IOCP Timeout ] IOCP_timeout=4000 [ Arranque minimizado en la barra ] [ Start minimized in tray ] Minimized=No [ Retraso necesario para las variables toggles (Project Magenta)] [ Deley needed for var. toggles (Project Magenta) ] toggle_delay=20 [ Fichero de configuracion ] [ Configuration File ] CONFIG_FILE=.\JeeHellWare.ssi [************** MONITOR MODULE ***************] [ Desabilitar monitorizacion remota del SIOC ] [ Remote monitor disable mode yes/no ] Monitor_disable=No [ Refresco broadcast monitor (en segundos) ] [ Broadcast monitor time (seconds) ] Monitor_time=2 [************** IOCARDS MODULE ***************] [ Desactivar el módulo de las IOCards ] [ Disable IOCards module ] IOCard_disable=No [ Divisor de frecuencia para los ejes analogicos (1-999). Retarda la entrega de valores. ] [ Frequency divisor for delay the analogic axes. (1-999)] Divisor_AD=10 [------------- CARDS CONFIG -------------] [ IOCard Master ] [...............] [ Spanish : ] [ MASTER=(Indice device),(Tipo),(Número de tarjetas),(Número device) ] [ Indice Device: Índice usado en la variable SIOC como device, para indicar a que tarjeta se hace referencia ] [ Se usa 0 en el caso de que sólo haya una tarjeta y no se tenga en cuenta el número de device, por defecto un script en SIOC cuando no se pone parámetro DEVICE, se hace referencia al índice 0] [ tipo = 0 : Emulador de Master Card // OBSOLETO ] [ tipo = 1 : Tarjeta Master conectada al puerto paralelo directamente // OBSOLETO ] [ tipo = 2 : Tarjeta Master conectada al puerto paralelo mediante cable de compatibilidad // OBSOLETO ] [ tipo = 3 : Placa de expansión por puerto paralelo // OBSOLETO ] [ tipo = 4 : Tarjeta USBExpansion usada ] [ tipo = 5 : Modulo MCP de Opencockpits ] [ tipo = 6 : Tarjeta USBOutputs ] [ tipo = 7 : Modulo EFIS de Opencockpits ] [ tipo = 8 : Modulo Radio COM de Opencockpits ] [ tipo = 9 : Modulo Radio NAV de Opencockpits ] [ tipo = 10 : Modulo Radio ADF de Opencockpits ] [ tipo = 11 : Modulo Radio ATC de Opencockpits ] [ tipo = 12 : Modulo Radio Airbus RMP de Opencockpits ] [ tipo = 13 : Modulo FMC-737 de Opencockpits ] [ tipo = 14 : Tarjeta USBDcmotorPLUS ] [ tipo = 15 : Modulo MCP V3 de Opencockpits ] [ tipo = 16 : Modulo CRONOMETRO B737 ] [ Número de tarjetas = Número de placas Master usadas, 1 a 4 para uso de placas de expansión, 1 para conexión de placa Master directa o del Emulador ] [ Número de device = 0 en el caso del Emulador o primera tarjeta USB detectada, Dirección del puerto paralelo (por ejemplo $0378), o número de dispositivo USB ] [ Un ejemplo de 2 USBExpansion conectadas con 3 y 2 placas Master ] [ MASTER=0,4,3,22 ] [ MASTER=1,4,2,24 ] [ Un ejemplo de conexión a simulador ] [ MASTER=0,0,1,0 ] [ English : ] [ MASTER=(Device index),(Type),(Number of cards),(Device number) ] [ Device index : Index used in SIOC variable like device, this is the card used for SIOC sentence ] [ Use 0 for only one card, for this value you not need specify Device number. If you not use DEVICE parameter in a definition in SIOC script, the default index used is 0] [ type = 0 : Master Card Emulator // OBSOLETE ] [ type = 1 : Master Card connected directly to parallel port // OBSOLETE ] [ type = 2 : Master Card connected throught compatibility cable to parallel port //OBSOLETE] [ type = 3 : Expansion Card connected throught parallel port //OBSOLETE ] [ type = 4 : USBExpansion Card used ] [ type = 5 : Opencockpits MCP module ] [ type = 6 : USBOutputs Card used ] [ type = 7 : EFIS module ] [ type = 8 : Radio COM module ] [ type = 9 : Radio NAV module ] [ type = 10 : Radio ADF module ] [ type = 11 : Radio ATC module ] [ type = 12 : Radio RMP Airbus module ] [ type = 13 : FMC-737 module ] [ type = 14 : USBDCmotorPLUS Card used ] [ type = 15 : MCP V3 module ] [ type = 16 : CHRONO B737 module ] [ Number of Cards = Master cards connecteds, 1 to 4 for expansion cards, 1 for a Master card directly connected or Emulator ] [ Number of device = 0 for Emulator or first USB card detected, parallel port address, device number for specifies USBexpansion card ] [ For example, two USBExpansion cards connected with 3 and 2 Master cards used ] [ MASTER=0,4,3,22 ] [ MASTER=1,4,2,24 ] [ For example, use of Master card emulator ] [ MASTER=0,0,1,0 ] [ Use the first USBExpansion card connected with only one Master Card attached ] [ Esta definición es para usar la primera tarjeta USBExpansion que se encuentre instalada que además llevará conectada una placa Master ] [MASTER=3,6,1,252] [MASTER=0,4,1,0] [MASTER=0,12,1,0] [MASTER=0,16,1,0] [ Others Cards / Otras tarjetas ] [...............................] [ Spanish : ] [ Nombre_de_tarjeta=(Indice device),(Número device) ] [ Indice Device: Índice usado en la variable SIOC como device, para indicar a que tarjeta se hace referencia ] [ Se usa 0 en el caso de que sólo haya una tarjeta y no se tenga en cuenta el número de device, por defecto un script en SIOC cuando no se pone parámetro DEVICE, se hace referencia al índice 0] [ Número de device = 0 para usar primera tarjeta USB de este tipo detectada ó número de dispositivo USB ] [ English : ] [ Name_of_card=(Device index),(Device number) ] [ Device index : Index used in SIOC variable like device, this is the card used for SIOC sentence ] [ Use 0 for only one card, for this value you not need specify Device number. If you not use DEVICE parameter in a definition in SIOC script, the default index used is 0] [ Number of device = 0 for first USB card of this type detected, or device number for a specifies device ] [ Ejemplo de dos USBServos en indices 0 y 1, y números de devices 17 y 23 ] [ Example of two USBServos for index 0 and 1, and device number 17 and 23 ] [ USBServos=0,17 ] [ USBServos=1,23 ] [USBStepper=0,0] [USBKeys=0,0] [USBServos=0,0] [USBRelays=0,0] [USBDCmotor=0,0] [ Para los ejes analógicos se usan los números de devices de las tarjetas donde están alojados ] [ For analogic axles, you use the device number of cards what allow the axles ] [USBAnalogic=0,0] [************** FSUIPC MODULE ***************] [ Desabilitar lectura de las FSUIPC ] [ FSUIPC disable mode yes/no ] FSUipcdisable=No [ Refresco recepción FSUIPC ] [ FSUIPC refresh ] FSUipcRefresh=50 [************** IOCP CLIENTS MODULES ***************] [ Retraso para inicializacion una vez conectado el cliente en milisegundos ] [ Delay for initialization when client has been connected in mseconds ] IOCPini_delay=3000 [************** IOCP CLIENT MODULE #0 ***************] [ Desactivar el módulo cliente IOCP ] [ Disable IOCP client module ] IOCPclient0_disable=No [ IP del servidor donde debe de conectar el cliente ] [ IOCP client host name ] IOCPclient0_host=localhost [ Puerto de envio del protocolo IOCP cliente ] [ IOCP client port ] IOCPclient0_port=8099 [************** IOCP CLIENT MODULE #1 ***************] [ Desactivar el módulo cliente IOCP ] [ Disable IOCP client module ] IOCPclient1_disable=yes [ IP del servidor donde debe de conectar el cliente ] [ IOCP client host name ] IOCPclient1_host=localhost [ Puerto de envio del protocolo IOCP cliente ] [ IOCP client port ] IOCPclient1_port=8099 [************** SOUND MODULE ***************] [ Ficheros de sonido ] [ Sound Files ] [ Desactivar el módulo de sonido ] [ Disable Sound module ] Sound_disable=yes [ Volumen general de los sonidos 0-100 ] [ Master Volume 0-100 ] Volume=100 [ put '*' first filename for loop Sound ] [ anteponer '*' en el fichero para bucle continuo de sonido] [ Sound=wav_file,frequency,volume,pan ] [ frequency=100 to 100000 0=original -1=current ] [ volume=0 to 100, -1=current ] [ pan=-100 (left) to +100 (right) 0=center -1=current ] [ Sound=Fichero_wav,frecuencia,volumen,balance ] [ frecuencia=100 hasta 100000 0=original -1=Por defecto ] [ volumen=0 hasta 100 -1=Volumen por defecto ] [ balance=-100 (Izquierda) hasta +100 (Derecha) 0=centro -1=Por defecto ] [ #1 ] Sound=APDis.wav,-1,-1,-1 [ #2 ] Sound=*outermk.wav,-1,-1,-1 [ #3 ] Sound=*hello.wav [************** KEYBOARD EMULATOR MODULE ***************] [ Nombre exacto de la ventana donde se enviarán las teclas ] [ Name of window for key send ] [window = "Project Magenta Glass Cockpit - Build 396" ] window =a.txt - Bloc de notas [ Asignación de teclas ] [ assign youe keys ] #1=A #2=B #3=C #4=D #5=E #6=F #7=G #8=H #9=I #10=J #11=K #12=L #13=M #14=N #15=O #16=P #17=Q #18=R #19=S #20=T #21=U #22=V #23=W #24=X #25=Y #26=Z #27=1 #28=2 #29=3 #30=4 #31=5 #32=6 #33=7 #34=8 #35=9 #36=0 #37=< #38=, #39=. #40=- #41=* #42=+ #43=// #44=/0 #45=/1 #46=/A #47= #48= #49= #50= #51= #52= #53= #54= #55= #56= #57= #58= #59= #60= #61= #62= #63= #64= #65= #66= #67= #68= #69= #70= #71= #72= #73= #74= #75= #76= #77= #78= #79= #80= #81= #82= #83= #84= #85= #86= #87= #88=<a #200=B [ --- SIOC Autoconfig Devices Ver 4.5B1 ==> 09.10.2013 06:05:00 <== ----] MASTER=1,4,1,11 MASTER=0,6,1,5

Would be nice if you can light up my brain... ;O)

Regards,
pero