New Opencockpits MCP v3 scipt ready

Hi,

A new lag-free SIOC script for Opencockpits MCP v3 can now be downloaded from
​Download - flightsim4fun.com
This script is supporting all new features in the the MCP v3, but should also work fine with MCP v2 ( I believe, don't have the MCP v2 so it is not tested by me).

This script is to be used with my OC4BA program, just unzip it to your OC4BA folder and rename the config line to: CONFIG_FILE=.\OCP4NGX_MCP_PP v1.10.ssi

Please report any issues, also if it works OK on your system.

rgs

Hi,

Its work perfect on MCPv1 from OC. Lags was drastically reduced, and improve on fast turns on encoders.

Take care to change DEVICE to 15 on SIOC.ini to mach with script


rgs

Hi

Works perfect on MCPv1. Lags drastically reduced and fast encoder inputs improve too.

take care to chage DEVIDE number to 15 on SIOC.ini to match with the script

rgs

Oops,

I forgot to tell that both the MASTER and CONFIG_FILE definitions in sioc.ini needs to be changed

Make sure that you have


1) CONFIG_FILE=.\OCP4NGX_MCP_PP v1.10.ssi in the CONFIG line of your sioc.ini
2) MASTER=15,5,1,nn ( where nn is your USB number) for older MCP than MCP v3
3) MASTER=15,15,1,nn ( where nn is your USB number) for MCP v3

Please also download again to make sure you have the latest files. The correct ZIP file should have a a installation note in it and the correct txt and ssi files.

Rgs

404 - Page Not Found ?

Quote:

---

Originally Posted by skino

404 - Page Not Found ?

---

Should be OK now.

Download - flightsim4fun.com

rgs

Remove the point at the end of the link

Quote:

---

Originally Posted by tiburon

Remove the point at the end of the link

---

Done now

rgs

Hi,

I am trying to run panel, sioc and oc4ba on remote pc and get a lag during rotation of knobs on MCP. Does somebody else tried given configuration and it is run smoothly?

Thanks,

I have one problem now not always but sometimes switches for A/T Arm and both F/D switches are opposite to what they show in FSX virtual cockpit...? any suggestions why...?

Thanks
Andy



Just some reverse engineering to get back simulation of these switches FOR OLDER MCP V3 VERSION THAT DOES NOT HAVE SPD-INV AND ALT-INV SWITCHES

HERE FIND IN NEW 1.10 VERSION SELECT BOLD RED TEXT IN YOURS AND PASTE OVER AL BELOW you will not have "//" there just select the lines that match

Code:

---

Var 2551 Static name SPEED_SW        // Link IOCARD_SW Device 15 Input 31 Type P

Var 2549 Static name SPD_INTV_SW    // Link IOCARD_SW Device 15 Input 37 TYpe P
Var 7001 name t_SPEED_SW Link IOCARD_SW Device 15 Input 31 Type I

{
IF &t_SPEED_SW = 1   
{
v7002 = DELAY 1 100
 }
 ELSE
{
}
 } 
 
 Var 7002 name s_delay // value 0
{
IF v7002 = 1
{
IF &t_SPEED_SW = 1
{
&SPD_INTV_SW = CHANGEBITN 0 &SPD_INTV_SW

}
ELSE
{
&SPEED_SW = CHANGEBITN 0 &SPEED_SW
}
ELSE
{
}
v7002 = 0
}
}

---

HERE FIND IN NEW 1.10 VERSION SELECT BOLD RED TEXT IN YOURS AND PASTE OVER AL BELOW you will not have "//" there just select the lines that match

Code:

---

Var 2522 Static name ALT_HLD_SW        // Link IOCARD_SW Device 15 Input 23 Type P
Var 2523 Static name ALT_INTV_SW    VALUE 0 // Link IOCARD_SW Device 15 Input 36 Type P
Var 7003 name t_ALT_HLD_SW Link IOCARD_SW Device 15 Input 23 Type I
{
IF &t_ALT_HLD_SW = 1   
{
v7004 = DELAY 1 100
 }
 ELSE
{
}
 } 
 
 Var 7004 name a_delay // value 0
{
IF v7004 = 1
{
IF &t_ALT_HLD_SW = 1
{
&ALT_INTV_SW = 1
&ALT_INTV_SW = DELAY 0 100
}
ELSE
{
&ALT_HLD_SW = CHANGEBITN 0 &ALT_HLD_SW
}
ELSE
{
}
v7004 = 0
}
}

---