Header Fly Engravity
  • How To Interface A Real VSI


    In behalf of MyCockpit Friends, thank you Stijn Baart (Stijn) and Rob Archer (737NUT) for contributing the following excellent informational tutorial.

    HOW TO INTERFACE A REAL VSI
    By Rob Archer (737NUT) & Stijn Baart (Stijn)


    Because nothing is more realistic than the real stuff.....

    !!!! We advise to read the tutorial and OpenCockpits USBservo manual before purchasing item’s !!!!



    This tutorial is a guide of how to interface a VSIgauge. But can also be used as an example for other real world gauges. Onething to keep in mind, is that the gauge has to be ‘’servo’d’’ .

    To make a gauge there are a few methods:

    • Interface a servo to the OC usbservo card and the servo will function as a needle. But we are limited to 180 degree movement.
    • An other alternative is the Dc motors card combined with a potentiometer. We could use a Dc motor for movement and the potentiometer to register the movement, with the help of some SIOC coding we could make it work like a gauge. Same concept as a servo but with more possibilities It increases the range of the needle but it requires some coding skill.
    For interfacing this VSI weare using both methods combined. The idea is to ‘’gut’’ theservo and replace the potentiometer and the Dc motor for the ones in the instrument.


















    For this Tutorial I will be using:

    • Sperry VSI (Flown on 737)
    • Futaba S 3001 (A similar model will do)
    • USBservo card
    • Screwdrivers
    • Soldering iron
    • Solder
    • Electrical wire (about 1.5 meter)
    • Electrical Tape
    • 5v Power supply
    Software installed:
    • USB servo tester
    • IOServos program
    • SIOC
    • FS2004 with FSUIPC
    Ok, We start with Identifying the wires andcomponents. Most instruments have the same lay-out, but components may lookdifferent or are placed some were else. A great recourse on how instrumentswork is this blog http://l1011project.blogspot.com/:

    Next we will ‘’gut’’ the servo. Just like flightinstruments are servos slightly different but have a basic lay-out. First wedisassemble the servo.


    When thecasing is removed we de-solder the Motor en potentiometer and replace 2 wiresfor the motor and 3 for the potentiometer. Write down or memorise which wire isconnected where.
    Ad some electrical tape between the potentiometer wireends. (I Didn’t for the photo)


    Modify if necessary the case so the wires fit throughthe holes, from the motor and potentiometer. When the case is back togetherconnect the wires to the potentiometer and motor inside the VSI. Again ad someelectrical tape between the joints.



    The next step is a rather important one. In most casesthe servo wires , the ones we connect the to the USBservo card, are notcorrectly arranged. So we have to rearrange them. Which in most cases is doneby lifting a safety pin on the connector and pulling the wire out. Or you can solder them directly to the card.

    Information on how to arrange the wires can be foundin the Opencockpits USBservo card manual.
    Download link for the manual : http://www.opencockpits.com/uploads/manual_usbservos_eng.pdf


    Now we connect a 5V power supply to the card (Note:it’s important that the wires are connected correctly + to + and – to – !!!)The servo can be connected too. Also these need to be connected as described inthe Opencockpits USBservo card manual.

    You should have a set up like this:


    The next step is to test the Gauge. Go ahead andconnect the usb cable and the 5V power supply.
    Then open the test software. By filling in a numberbetween 1 and 1023 or moving the slide bar the needle should be moving. Thiscan be used to get the value’s to use in your script.

    The test program can be downloaded here: http://www.opencockpits.com/modules.php?name=Downloads&d_op=getit&lid=252


    Then make sure to modify SIOC.INI So it recognises theUSBservo card.
    The index and device number can be different dependingon how what and how many cards you have.
    If unfamiliar with this we advise to study theinformation on http://www.lekseecon.com/


    Finally we have to write a script for the gauge towork. It is possible to use this or existing scripts and change the variablesand value’s. This is the script I used:





    The result: à



    Now youshould have a working VSI

    !!Good luckwith Yours!!