PDA

View Full Version : 100 mm linear taper slide potentiometer



Tnoble
04-19-2010, 07:39 PM
Does anyone know where I can find some 100 mm linear taper (B) slide potentiometers? The cheapest I can find are $15 each!
Thanks

Tripacer
04-19-2010, 10:21 PM
I am using Bourns linear pots with a hig duty cycle. It is part number
PTF01-152A-103B2
This is a Mouser part number. I paid $5.52 a while back.

See; www.mouser.com

Tripacer

Ronson2k9
04-19-2010, 11:22 PM
I have a related question.

Is there a difference between stereo and mono pots as it relates to sim building? I've been able to find 100k pots but they are in stereo. Should I be looking for a particular type of pot? As I look at the Mouser catalog page it seems the above pot is used for mixing as well as other audio apps. Is that the case for all slide pots or just the principal use for them?

Well okay a few related questions .. trying so hard to not sound like a newbie though..

Tnoble
04-19-2010, 11:30 PM
Thanks for the info on mouser. Unfortunately that is only a 45 mm slide. I am using these for cessna- type throttle/mixture/prop and need at least 3-3/8" of travel so anything less than 100 mm will be too short.

Wendy
04-20-2010, 01:17 AM
Stereo pots are 2 pots in one house. That's all. You should look for lineair pots, most pots used in audio will be logaritmic.

Regards, Wendy

kermit
04-20-2010, 01:27 AM
HI , I`m using real Cessna throttle and mixture units,
80 mm will be enough for full in to full out
greetz

AK Mongo
04-20-2010, 11:56 AM
Mouser also sells a linear 100mm pot. i will try to find a part number. I just ordered and interfaced them into my cessna (210) TPM controls. The Prop and mixture each would have worked with an 80mm pot, but the throttle required 93mm of travel. Will try to get you the Mouser part later today...

Tripacer
04-20-2010, 02:09 PM
The Mouser Part Number has a 652 in front of the Bourn part number, therefore,

652-PTF01-152A-103B2 for a 100 mm pot. I used one on my throttle. And yes these are stereo pots which menas that there are two pot circuits in one case. I hooked up one side to my Opencockpits board and it works just fine.

Tripacer

AK Mongo
04-20-2010, 02:19 PM
The Mouser Part Number has a 652 in front of the Bourn part number, therefore,

652-PTF01-152A-103B2 for a 100 mm pot. I used one on my throttle. And yes these are stereo pots which menas that there are two pot circuits in one case. I hooked up one side to my Opencockpits board and it works just fine.

Tripacer

Same thing I did, although I hooked them into my ch yoke interface and replaced the three top levers.

Tnoble
04-20-2010, 10:05 PM
Great, Thanks a lot guys. I plan to hook these into in leo bodnar joystick controller. So as far as stereo vs. mono are you saying that the only difference is that there are two outputs for ther stereo pot? therefore all I have to do is use one of the outputs and ignore the other?

AK Mongo
04-20-2010, 10:13 PM
That is all! They are six lugs marked 1, 2 and 3. Use one of each on the same side of the slider and you are golden! #2 is the wiper, btw.

Ronson2k9
04-21-2010, 12:02 AM
Cool thanks for the info...

Tripacer
04-21-2010, 12:22 AM
I have uploaded a picture of the connection between a Bourns 100mm linear pot and a push-pull throttle on my pit in the Genereal aviation section. I made a metal bracket to mount the pot with a slot for the slide to move in. I machined a small aluminum connector to join the throttle shaft and the pot slide. I had to drill a small hole in the pot slide (1/16" I think). It works well. I need to ensure that there are physical stops on the throttle shaft instead of allowing the pot to just bottom out.
Hope this helps.
If I could figure out how to paste in a pic in a forum reply you would not have to run over to the photo gallery.

Tripacer

Ronson2k9
04-21-2010, 12:52 AM
What I do is upload the image to Photobucket (http://photobucket.com/) or other such photo storage site then paste the image link here. Works like a charm.

HansJansen
04-30-2010, 10:07 AM
The Mouser Part Number has a 652 in front of the Bourn part number, therefore,

652-PTF01-152A-103B2 for a 100 mm pot. I used one on my throttle. And yes these are stereo pots which menas that there are two pot circuits in one case. I hooked up one side to my Opencockpits board and it works just fine.

Tripacer

Hi,

Are you sure this is a linear taper pot? Stereo pots (used in audio equipment) usually have logarithmical taper, which is NOT what you want in sim controls!

Also, according to Mouser's data sheet for this potmeter, it has only 60 mm travel, so beware...

Regards,

cjellwood
03-06-2011, 09:39 PM
The pot subject is baking my noodle at the moment. On the lookout for 80mm slide pot so would be intereted to hear about any success in that department.

There is something on this page so will send an enquiry
http://www.nobleusa.com/slide.html

thanks
Chris

AK Mongo
03-06-2011, 10:23 PM
Chris,

Won't hurt if you have to go a little long. I used 100mm pots (Bourn PTF01-152A-104B2). They provide a little extra travel, but calibrating them via fs or fsuipc renders that a non-issue. The only one who will know is you... ;)

Reid

cjellwood
03-07-2011, 05:03 AM
Chris,

Won't hurt if you have to go a little long. I used 100mm pots (Bourn PTF01-152A-104B2). They provide a little extra travel, but calibrating them via fs or fsuipc renders that a non-issue. The only one who will know is you... ;)

Reid

I know what you are saying AK, that has crossed my mind. The firm that has 80mm slides replied to me very early this morning requesting company details from me prior to quoting, hopefully they have a spec sheet for us soon.

Chris

cjellwood
03-07-2011, 01:30 PM
There seems to be a healthy cheap supply of 65mm pots so may settle for them
http://www.allelectronics.com/make-a-store/item/SLP-10K4/10K-LINEAR-SLIDE-POT-4-CHANNEL/1.html

Chris

Leo Bodnar
03-07-2011, 02:14 PM
It's good idea to check the datasheet if available - a lot of cheap pots are rated for 10K movements or less and designed to be used in things like tone control that you adjust once in a blue moon. In any case try mounting it with a slot facing downwards to stop dust falling through.

cjellwood
03-07-2011, 02:32 PM
how about these type available from http://www.partridgeelectronics.co.uk/17Dresistors.htm

http://www.leons-world.com/img/17-183.jpg

Probably better quality than the $1 stinker I suspect.

Chris

Leo Bodnar
03-07-2011, 02:46 PM
Penny + Giles is top stuff used in mix desks but they are most definitely log taper (audio.)

cjellwood
03-08-2011, 06:33 AM
I kind of regret posting that fader control pic lol, it only shows desperation and minimal thought on my half lol

Chris

Leo Bodnar
03-08-2011, 02:31 PM
I have found these if it helps:
http://uk.farnell.com/bourns/ptb0143-2010bp-b103/potentiometer-slide-10k-100mm/dp/1688409
http://uk.farnell.com/panasonic/evajqlr15b14/potentiometer-slide-10k/dp/8795959

anatoliy
09-20-2013, 06:29 PM
Hey all, Does anyone have a picture or can explain how to install linear taper slide potentiometer with BU0836X Joystic board. On my potentiometer 2 connections on one side and 4 on the other.